Qianli Bumblebee Stencil (QS66) Qualcomm PM Series 1
₨ 600
QS66 PMIC Reballing Stencil
The Qianli Bumblebee Stencil (QS66) Qualcomm PM Series 1 puts a wide range of Qualcomm power-management ICs on one reballing plate. You get square holes with rounded angles for clean solder ball placement on PM8998, PM660, PM8937, PMI8998 and the rest of the QS66 chip list. Technicians use this Qianli QS66 PMIC reballing stencil to rebuild a removed power IC before it goes back on the board. Each order ships as one stencil, ready for your reballing bench alongside a hot air station and a reballing kit.
In stock
Qianli QS66 PMIC Reballing Stencil for Qualcomm Power ICs
The Qianli QS66 PMIC reballing stencil covers the Qualcomm PM Series 1 power-management chips that sit behind most dead phone and charging issue repairs. Mechanicpk supplies the Qianli Bumblebee Stencil (QS66) Qualcomm PM Series 1 to Pakistani repair shops that reball power ICs in-house instead of replacing the chip every time a lifted ball or damaged pad stops a job. The plate lists nineteen supported chips, from PM8226 and PM8084 through PM8998 and PMI8998, so a single stencil serves many different boards on your bench.
Chip Coverage: PM8998 Reballing Stencil and More
QS66 belongs to Qianli’s Bumblebee series. The supported list reads PM8821, PM886EAD, PM09635, PM8028, PM820EAD, PM8029, PMI8952, PM8952, PMI8994, PM8994, PM8937, PM660, PM8940, PMI8940, PMI8937, PMI8998, PM8998, PM8084 and PM8226. Read the marking on your IC and match it against this list before you order, because the stencil follows the chip, not the phone model. The same rule applies when you buy a PM8998 reballing stencil or any other Qualcomm PMIC stencil: the chip number decides compatibility. This listing sticks to the verified chip list and makes no claims about specific handsets.
Stocking one QS66 plate covers nineteen PMIC part numbers with one tool instead of a drawer of single-chip stencils. That shortens the search when a board lands on your bench and gives every technician in the shop one plate to learn. Pair it with the right solder paste, flux and a steady hot air station, since a good stencil only pays off when your temperature and technique hold up. Mechanicpk ships the QS66 as one stencil per pack.
Square Holes, Rounded Angles, Repeat-Use Build
Qianli builds QS66 with square holes and rounded angles. Square openings let solder balls settle into each aperture, and the rounded corners help the formed ball release cleanly when you lift the plate after reflow. Qianli describes the stencil as sturdy, precise and durable over time, with a newer treatment and materials that make it easier and more precise to use. A workshop that reballs power ICs every week benefits from that durability, because a worn or bent plate gives uneven balls and forces a second reflow.
Handle the plate flat, clean flux residue off it after each job, and store it away from other metal tools so the apertures stay sharp. Secure it over the IC with heat-resistant tape or a stencil holder so it cannot shift while you work.
Using QS66 in a Qualcomm PMIC Repair Workflow
Most PMIC jobs start with a multimeter. You check the battery and charging rails, find a short or a dead rail, and trace the fault back to the power IC. Once you confirm the chip is the problem, lift it with a hot air station, clean the pads on the board and the IC with your soldering station and wick, and inspect the pads under a microscope. Next, clamp the board in a PCB holder, align the QS66 plate over the IC’s contact pattern, fill the apertures with solder paste or balls, and reflow with controlled heat. Lift the stencil after the chip cools, check the ball array for gaps, and refit the IC. Our Reballing Kits category carries the paste, balls and accessories for this step.
A dead phone or a charging issue that traces back to the PMIC often ends at this bench. If the phone still hangs on logo after the power section tests clean, move to the software and storage side with eMMC Programmers, UFS Adapters and ISP Pinout Tools, and use Test Boxes to confirm the phone before you close it. As your volume grows, upgrade from a basic iron to a stable hot air station and a better microscope. Keep a Qianli QS66 PMIC reballing stencil at each bench that handles power-section work, so nobody waits for a shared plate.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Covers 19 Qualcomm PM and PMI chips on a single plate
- ✓Square holes with rounded angles for ball placement
- ✓Part of the Qianli Bumblebee reballing stencil series
- ✓Sturdy, precise build that Qianli rates as durable over time
- ✓Newer treatment and materials for easier, more precise use
- ✓Suits PMIC reballing in dead phone and charging issue repairs
- ✓Pairs with hot air stations, reballing kits and microscopes
- ✓Supplied as 1x stencil
Specifications
| Brand | Qianli |
|---|---|
| Model | QS66 |
| Category | BGA Reballing Stencil (Bumblebee Series) |
| Compatibility | Qualcomm PM Series 1 power-management ICs |
| Supported Devices | Chip-level, universal across phones that use the listed ICs (not device-specific) |
| Technology | BGA reballing stencil with square holes and rounded angles |
| Package | 1x Stencil |
Common Repair Uses
- ✓Reballing Qualcomm power-management ICs on the repair bench
- ✓Reballing a removed Qualcomm PMIC before refitting it
- ✓Dead phone repairs traced to a faulty power IC
- ✓Charging issue repairs where the power IC needs rework
- ✓Rebuilding a PMIC that has lifted or damaged balls
- ✓Reusing a good donor PMIC after cleaning and reballing
- ✓Rework after short-circuit diagnosis on a main power rail
- ✓Reball and reflow jobs with microscope inspection of the ball array
- ✓Practice reballing for technicians and training institutes
Compatible Devices
- ✓Chip-level compatibility with the Qualcomm PM Series 1 ICs below; not device-specific
- ✓PM8821, PM886EAD, PM09635
- ✓PM8028, PM820EAD, PM8029
- ✓PMI8952, PM8952
- ✓PMI8994, PM8994
- ✓PM8937, PM660
- ✓PM8940, PMI8940, PMI8937
- ✓PMI8998, PM8998
- ✓PM8084, PM8226
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which Qualcomm PMIC chips does the Qianli QS66 stencil support?
Can I use the QS66 stencil to reball PM8998 and PM660?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



