2UUL DA90 BB Nano Superpower Fan 30W Cooling Dust Blower
₨ 6,600
2UUL DA90 Cooling Fan
The 2UUL DA90 BB Nano Superpower Fan 30W gives your repair bench a pocket-sized turbine blower for cooling boards and clearing dust. A 30W turbine motor drives a directional airstream, two speed modes let you match airflow to the job, and a 1300 mAh battery with USB-C charging keeps it cordless. At 92 × 47 × 47 mm and 101 g, it fits a service bag or sits beside your soldering station. Use it to cool components after soldering, blow lint out of charging ports and connectors, and clean boards before inspection under the microscope.
In stock
2UUL DA90 Cooling Fan Built for Precision Repair Benches
The 2UUL DA90 BB Nano Superpower Fan 30W puts a compact turbine blower on your bench for two jobs that come up in every repair: pulling heat off a board and clearing dust out of tight spots. If you need a 2UUL DA90 cooling fan that sits next to a soldering station without taking up space, this unit measures 92 × 47 × 47 mm and weighs 101 g. 2UUL rates the motor at 30W and pairs it with a 1300 mAh battery, so the fan runs cordless and recharges through USB-C. Technicians who already work with hot air stations and microscopes will see where it fits in the workflow right away.
Turbine Motor and Two-Speed Control
The 30W turbine motor produces a directional airstream, so you aim the airflow at one IC, one connector, or one corner of a board instead of blowing air across the whole bench. A turbine design concentrates air into a narrow stream, which suits board-level work better than a wide desk fan. 2UUL does not publish airflow or noise figures for the DA90, so judge it by the job: it delivers focused blowing force from a very small body. Two speed modes, low and high, cover light and heavy work. Press the button twice while the fan is off to start on low, tap once during operation to switch speed, and hold the button to stop. The illuminated indicator shows green above 50% battery, blue below 50%, and red below 10%, so you know when to plug in before the next board.
Dust Blower for Mobile Repair Boards and Ports
Every board that reaches your bench carries pocket lint, carbon residue, or fine dust, and a dust blower for mobile repair saves you from scraping at it with a brush. The nozzle reaches ports, sockets, and connectors, and the airflow clears micro-cracks and tight gaps. Use it on a charging port when a charging issue traces back to packed debris, on a camera lens module before reassembly, or on a keyboard or smartwatch board that needs a quick clean. After soldering, the same airflow blows slag and loose debris off the work area. Cooling works without contact: you direct the stream at a component during soldering or testing and bring its temperature down without touching the part. That helps when you rework a hardware fault on a dead phone and need to move to the next step quickly. A simple routine works well: clean the port, cool the part, then inspect under the microscope.
Battery and USB-C Charging at the Bench
A 1300 mAh battery makes the fan cordless, so no cable crosses your work area while you hold a hot air gun or a soldering iron. Charging runs through the USB-C port at 5V and 2A and takes about 60 minutes, which suits a break between repair batches. At 101 g, the DA90 rides in a service bag for onsite jobs and sits comfortably on a shared bench in a busy shop. Pair it with hot air stations and soldering stations for rework, a microscope for inspection, PCB holders to keep boards steady, a multimeter to confirm the repair, and reballing kits for BGA work. The fan covers the cooling and cleaning steps around each of those tools. For buyers comparing options, the verified figures are simple: 30W rated power, 1300 mAh battery, 5V 2A USB-C input, two speeds, a 92 × 47 × 47 mm body, and 101 g net weight. This is a general-purpose bench accessory, not a device-specific tool, so it works with any phone, tablet, or board you service in your Pakistan repair workshop.
| Weight | 0.31 kg |
|---|
Key Features
- ✓Cooling and cleaning steps around soldering, rework, and testing.
- ✓Cooling components after soldering
- ✓Cooling circuits during testing without contact
- ✓Clearing lint from charging ports when diagnosing a charging issue
- ✓Blowing dust out of sockets and connectors
- ✓Cleaning boards before microscope inspection
- ✓Removing slag and loose debris after rework
- ✓Dusting camera lens modules before reassembly
- ✓General cleaning of keyboards and small electronics
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL DA90 BB Nano Superpower Fan 30W (BB Nano turbine fan, product code DA90) |
| Technology Entity | 30W turbine motor, 1300 mAh rechargeable battery, USB-C charging |
| Compatible Device Entities | smartphone motherboards, charging ports, camera lens modules, smartwatches, earphones, keyboards |
| Repair Process Entity | component cooling during soldering and testing, dust and debris removal, board cleaning before inspection |
| Industry Entity | Mobile repair, GSM service, PCB repair, precision electronics |
Common Repair Uses
- ✓Universal bench accessory, not device-specific. It works around any phone, tablet, or board you service.
- ✓Smartphone motherboards (all brands)
- ✓Charging ports and USB sockets
- ✓Board-to-board and FPC connectors
- ✓Camera lens modules
- ✓Smartwatch boards
- ✓Earphones and headphones
- ✓Keyboards
- ✓General precision electronics and PCBs
Compatible Devices
- ✓30W turbine motor with directional airflow
- ✓Two speed modes, low and high
- ✓1300 mAh built-in battery for cordless use
- ✓USB-C charging at 5V 2A, about 60 minutes to full
- ✓Illuminated battery indicator: green above 50%, blue below 50%, red below 10%
- ✓Pocket-sized 92 × 47 × 47 mm body
- ✓Lightweight 101 g net weight
- ✓Contactless component cooling and dust removal in one tool
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How long does the 2UUL DA90 take to charge and what input does it need?
How do I start the 2UUL DA90 and change speed?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



