2UUL SC08 UV Curing Lamp – 365-395nm Dual Band
₨ 1,600
Compact UV Curing Lamp for PCB Repair
The 2UUL SC08 UV curing lamp gives your repair bench a cordless, pocket-sized UV LED source for spot curing on mobile phone motherboards. Its 365-395nm dual-band output cures shadowless glue, UV adhesive, optical glue, resin glue and photosensitive solder mask (green oil). You recharge it through the built-in Type-C interface, hold it over the coated area, and cure in seconds without moving the board into a curing box. The 25.5g aluminum alloy body with silicone buttons keeps it light enough for long sessions next to your microscope and hot air station. Mechanicpk supplies it for technicians who want controlled curing after BGA and trace repair.
In stock
2UUL SC08 UV Curing Lamp for Board-Level Curing Work
The 2UUL SC08 UV curing lamp is a handheld, battery-powered UV LED source designed for the curing tasks that follow board-level repair on mobile phone PCBs. It emits across a 365-395nm dual band, the range that UV-reactive adhesives, shadowless glue and photosensitive solder mask respond to. Because it weighs 25.5g and runs cordless, you bring the light to the board instead of clamping the board under a fixed lamp. Mechanicpk supplies this model to repair shops and service centers that cure small areas under a microscope and need precision rather than a large curing chamber.
Dual-Band 365-395nm Output and Cure Speed
The lamp combines two LED wicks that cover both ends of the 365-395nm band, so one tool handles a wider range of UV-curable materials than a single-wavelength torch. Supplier documentation states that holding the lamp over the coated area for 3-5 seconds produces a curing effect. You can cure shadowless glue, UV glue, optical glue, resin glue, ink and green oil with the same lamp. The LED source also draws little power compared with older UV tubes, so you can run repeated short cures across a full shift without waiting for a warm-up. Wear UV protective eyewear and keep the beam away from your eyes and skin during use.
Where It Fits in the Board Repair Workflow
Your cure step comes after the soldering and rework steps. Once you finish IC change karna, BGA reflow or a reballing job with your hot air station and reballing kit, you may need to protect exposed pads or traces. Apply green oil over a repaired trace or jumper point, then cure it with the SC08 to restore the insulating mask layer. The same lamp fixes optical glue and UV adhesive during assembly and sets bonding material around a chip you worked on. Technicians fixing a charging issue or other hardware fault on a damaged board use it to seal the repair before they reassemble the phone. Pair it with a microscope for placement, a multimeter for continuity checks, and a PCB holder to keep the board steady while the compound cures.
Cordless Handling and Type-C Charging
A built-in rechargeable battery lets you work without a power cable tying you to the bench, and the Type-C interface charges from a standard 5V/1A input. The lamp measures 76 x 32 x 21mm, so it fits your tool tray or shirt pocket. An aluminum alloy shell protects the internals, and silicone buttons give you a firm press when you wear gloves or work with flux on your fingers. Keep the lamp in your regular carry kit alongside your soldering station and tweezers, and charge it between jobs. For shops that run several boards a day, a lamp that stays ready on the bench saves real time compared with a shared curing station.
| Weight | 0.25 kg |
|---|
Key Features
- ✓365-395nm dual-band UV LED output for a wide range of UV-curable materials
- ✓Cures at the glue coating in about 3-5 seconds per supplier documentation
- ✓Cordless operation with built-in rechargeable battery
- ✓Type-C charging interface, 5V/1A input
- ✓Dual LED wicks, energy efficient with long service life
- ✓Aluminum alloy metal shell with silicone buttons
- ✓Compact 76 x 32 x 21mm body at 25.5g net weight
- ✓Suited to shadowless glue, UV glue, optical glue, green oil, resin glue and ink
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC08 |
| Category | UV Curing Lamp / Mobile Repair Tools |
| Compatibility | Universal – not device-specific |
| Technology | Dual-band 365-395nm UV LED |
| Material | Aluminum alloy shell, silicone buttons |
| Input Voltage | 5V/1A |
| Output Voltage | 3.7V/1A |
| Dimensions | 76 x 32 x 21mm |
| Weight | 25.5g (net) |
Common Repair Uses
- ✓Spot curing of UV-curable materials during and after mobile phone board repair
- ✓Curing green oil over repaired traces
- ✓Sealing jumper points after trace repair
- ✓Curing shadowless glue and UV adhesive
- ✓Setting optical glue during assembly
- ✓Curing resin glue around chips after IC change karna
- ✓Protecting pads after BGA reballing
- ✓Curing UV-curable ink marks on boards
- ✓Sealing small repairs after charging issue fixes
Compatible Devices
- ✓Universal UV curing tool, not tied to a specific phone model; works on any board coated with UV-curable material, including iPhone and Android motherboards
- ✓iPhone motherboards
- ✓Android phone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno and others)
- ✓Mobile phone PCB repair areas
- ✓BGA chip areas after reballing
- ✓Boards coated with photosensitive green oil
- ✓Assemblies bonded with UV adhesive
- ✓Assemblies bonded with optical glue
- ✓Boards coated with resin glue or UV-curable ink
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which UV wavelength does the 2UUL SC08 cover?
How long does the 2UUL SC08 take to cure UV glue or green oil?
Related products
RELIFE RL-004SA silicone pad – Anti-slip
In stock



