Amaoe Stencil SWT1 Smartwatch & POS BGA Reballing Stencil

₨ 599

Smartwatch and POS BGA Reballing Stencil

Amaoe Stencil SWT1 is a 0.12 mm steel mesh BGA reballing stencil for smartwatch and POS machine board repair. It carries twelve entries: PM8916, BGA162, MSM8909W RAM, MSM8909W CPU in large and small hole layouts, SC2721G, SL8521E, BCM47755, WCN3610, WRT2965, SR3593A and FS1896. You place the stencil over a cleaned chip, fill the apertures with solder paste or balls, and reflow to restore even ball height before you refit the IC. Mechanicpk supplies this Amaoe stencil to technicians and repair shops across Pakistan who work on compact wearable and payment terminal boards.

In stock

11 People watching this product now!
Description

Amaoe Stencil SWT1 for Smartwatch and POS Chip Reballing

Amaoe Stencil SWT1 gives you a dedicated reballing template for the compact chips that sit on smartwatch and POS machine boards. After you lift a chip with a hot air station, the original solder balls are gone or uneven, and the IC needs fresh, uniform balls before it goes back on the board. This stencil handles that step with 0.12 mm steel mesh apertures laid out for the chips named in the SWT:1 listing. If you repair wearables or payment terminals, it replaces guesswork on small packages with a fixed pattern you can repeat on every board.

Chip Coverage and Stencil Layout

The SWT:1 pattern set covers PM8916, BGA162, MSM8909W RAM, SC2721G, SL8521E, BCM47755, WRT2965, SR3593A, WCN3610 and FS1896. For the MSM8909W CPU, the stencil carries two aperture sizes, a large hole and a small hole, so you choose the layout that matches the ball size on your chip. MSM8909W and PM8916 are Qualcomm parts, and BCM47755 is a Broadcom part, which tells you the stencil targets the silicon found on smartwatch logic boards rather than mainstream phone motherboards.

Check the marking on your chip against this list before you start. A stencil only works when its aperture grid matches the package footprint, and a universal grid forces you to compromise on pitch and alignment. A chip-specific pattern removes that compromise. You spend less time shifting the stencil by fractions of a millimetre, and you lose fewer chips to bridged or missing balls. The 0.12 mm mesh thickness sets the paste or ball volume per pad, which keeps ball height consistent across the whole package once you reflow.

Where It Fits in Your Rework Workflow

Smartwatch and POS repair follows the same board-level sequence as phone repair, only on smaller packages. You trace the fault, remove the suspect IC with hot air, clean the pads and the chip, then reball. The stencil sits in the reballing step. Secure the chip in a holder or reballing platform, align the apertures to the pads under a microscope, and press paste through the mesh or drop in balls.

Heat the chip until the balls form, lift the stencil, and inspect every ball for size and position. A clean result gives your refit even contact on every pad. Technicians who chase a dead watch, a charging issue or a hang on logo fault use this step after they trace the problem to a chip joint, so they know the IC itself starts with healthy balls when they place it back.

Work at a temperature your paste and chip tolerate, and give the board time to cool before you lift the stencil, since pulling it away from hot balls can drag them off position. Rework on smartwatch boards leaves little margin, so a steady, repeatable method matters more than speed.

Keep the stencil flat after use. Wipe flux and paste residue off the mesh with isopropyl alcohol and a soft brush, because clogged apertures leave uneven balls on the next chip.

Pairing the SWT1 with Your Bench Tools

Stencil work depends on the gear around it. A hot air station with stable airflow control reflows small balls without blowing paste off the pads. A soldering station and desoldering wick handle pad cleanup before you reball. A microscope makes alignment on tiny packages realistic, a PCB holder keeps the board steady, and a reballing kit supplies solder balls and paste in the right size.

Browse the Hot Air Stations, Soldering Stations, Microscopes, PCB Holders and Reballing Kits categories at Mechanicpk to build the full bench around the SWT1. Repair shops and service centers in Pakistan that handle wearables and POS terminals can order the stencil together with the consumables and equipment for the complete job, from chip removal to final inspection.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.12 mm steel mesh for consistent ball height
  • Twelve chip entries on a single SWT:1 stencil
  • Separate large and small hole layouts for the MSM8909W CPU
  • Built for smartwatch and POS machine board repair
  • Chip-specific aperture grids instead of a generic pattern
  • Works with solder paste or solder balls
  • Reusable after cleaning
  • Pairs with hot air stations, reballing platforms and microscopes

Specifications

BrandAmaoe
ModelSWT:1
CategoryBGA Reballing Stencils
CompatibilitySmartwatch and POS machine chips listed under Compatible Devices
Supported DevicesSmartwatch and POS machine boards
TechnologyBGA reballing, 0.12 mm steel mesh stencil

Common Repair Uses

  • Board-level reballing on smartwatch and POS machine boards.
  • Reballing a smartwatch CPU (MSM8909W) after removal
  • Reballing the PM8916 power management IC
  • Reballing MSM8909W RAM
  • Reballing SC2721G and SL8521E on smartwatch boards
  • Reballing BGA162 packages on POS machine boards
  • Reballing BCM47755 and WCN3610 after chip removal
  • Rebuilding balls on WRT2965, SR3593A and FS1896
  • Restoring uniform ball height before refitting a cleaned IC

Compatible Devices

  • Chip-level compatibility for smartwatch and POS machine boards. The stencil is chip-specific, not device-model specific.
  • PM8916
  • BGA162 package
  • MSM8909W RAM
  • MSM8909W CPU (large hole)
  • MSM8909W CPU (small hole)
  • SC2721G and SL8521E
  • BCM47755 and WCN3610
  • WRT2965, SR3593A and FS1896

FAQ

What is the product name?
The product name is Amaoe Stencil SWT1.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is SWT:1.
What is this product used for?
This product is used for reballing BGA chips on smartwatch and POS machine boards.
Which devices are compatible with this product?
This product is compatible with smartwatch and POS machine boards that use PM8916, BGA162, MSM8909W RAM, MSM8909W CPU, SC2721G, SL8521E, BCM47755, WRT2965, SR3593A, WCN3610 or FS1896.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which chips does the Amaoe SWT1 stencil support?
The SWT:1 stencil supports PM8916, BGA162, MSM8909W RAM, MSM8909W CPU in large and small hole layouts, SC2721G, SL8521E, BCM47755, WRT2965, SR3593A, WCN3610 and FS1896.
Does the Amaoe SWT1 cover both large and small hole MSM8909W CPU layouts?
Yes. The SWT:1 lists the MSM8909W CPU in both a large hole and a small hole layout, so you match the aperture to the ball size on your chip.