Amaoe SU3 BGA Reballing Stencil for Spreadtrum CPU

₨ 599

SU3 Stencil for Spreadtrum ICs

The Amaoe SU3 BGA reballing stencil gives your repair bench a 0.12mm Japanese steel template built around Spreadtrum chips, including SC9863A, SC9832E, SC2721G and several related ICs. Square apertures guide each solder ball into place, so you restore a clean ball array after every chip-off job. The steel resists deformation and handles repeated reballing cycles. Pair it with your hot air station, microscope and reballing platform to finish IC change work on dead phone and hang on logo boards. Mechanicpk supplies the SU3 to technicians and workshops across Pakistan.

In stock

14 People watching this product now!
Description

Amaoe SU3 BGA Reballing Stencil for Spreadtrum Chip Rework

The Amaoe SU3 BGA reballing stencil gives you a dedicated 0.12mm steel template for Spreadtrum SC-series ICs. You lay it over a cleaned chip, push solder balls through the square apertures, and heat the template to rebuild a uniform ball array on the CPU or support IC it targets. When Spreadtrum boards reach your bench as dead phone cases, hang on logo faults or charging issue repairs with damaged BGA joints, this stencil replaces guesswork with a repeatable ball layout. Mechanicpk supplies the SU3 as a chip-matched tool for technicians who already know their rework process.

Chip-Level Coverage You Can Verify Before You Order

Distributor listings map the SU3 to the SC9863A and SC9832E processors, the BGA254 package, and the SC2721G, SR3595D, SR3593A, RPM6743-31 and RTM7916-51 ICs. The same Amaoe series includes the SU1 and SU2, and each one targets different SC part numbers, so the SU3 does not substitute for them. Read the marking on the chip you removed, then match it against this list before you buy. Each stencil carries one pad layout, and a wrong match costs you a full rework cycle. Listings do not publish a phone-model list, so this page scopes compatibility to the chip level and leaves device guesses out. If your shop runs Spreadtrum chip-off jobs every week, keep the SU1, SU2 and SU3 together so every chip family has a matching template.

Steel Build and Aperture Design

Amaoe cuts the SU3 from Japanese steel sheet at 0.12mm thickness with square holes. Listings describe the steel as super hard and deformation resistant, and the template stays reusable across repeated reballing jobs. Thin, rigid steel lies flat against the chip face, so each ball drops into its own aperture and your reflow stays clear of neighbouring pads. Square apertures define the ball position and keep your array consistent from chip to chip. Care matters as much as material. Wipe flux residue off the stencil with isopropyl alcohol after each job, dry it, and store it flat so the apertures stay clear. A clean template keeps ball placement accurate and extends the life of a tool built for repeated use.

Where the SU3 Fits in Your Reballing Workflow

Start by lifting the IC with your hot air station or rework station, then clean the chip face with your soldering station and wick until the pads sit flat. Inspect the pads under your microscope, because leftover solder blocks alignment. Hold the chip in a reballing platform or PCB holder, lay the SU3 over it, and line up every aperture with its pad. Match your solder ball size to the stencil apertures and test-fit a few balls before you commit to the full chip. Apply a thin, even layer of flux so the balls seat and hold during heating. Keep the chip steady in a holder instead of your fingers, because a slipped stencil forces you to clean and start again.

Spread the balls, heat the template, let it cool, and lift it away to reveal a fresh ball grid. After you place the chip back on the board for IC change karna, check for shorts with your multimeter before you software marna or flash the phone. That sequence stops you from reflashing a board that still carries a hardware fault. Repair shops that handle Spreadtrum phones daily keep the SU3 beside their reballing kits, so the template is ready the moment a chip-off job arrives.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.12mm thickness for flat, controlled ball placement
  • Japanese steel sheet construction
  • Super hard, deformation resistant steel
  • Square holes for defined ball positioning
  • Reusable across repeated reballing jobs
  • Targets SC9863A, SC9832E and BGA254 packages
  • Also covers SC2721G, SR3595D, SR3593A, RPM6743-31 and RTM7916-51
  • Part of the Amaoe SU series for Spreadtrum chips

Specifications

BrandAmaoe
ModelSU3 (also listed as SU-3 and SU:3)
CategoryBGA Reballing Stencil
CompatibilitySpreadtrum SC-series CPU and related ICs
TechnologyBGA reballing template, 0.12mm thickness, square holes, reusable
MaterialJapanese steel sheet

Common Repair Uses

  • Chip-off reballing of Spreadtrum ICs on mobile phone boards
  • Reballing a removed Spreadtrum CPU before refitting
  • Restoring solder balls on SC2721G after chip removal
  • Reballing SR3595D and SR3593A ICs during board repair
  • Preparing RPM6743-31 and RTM7916-51 for refit
  • IC change karna jobs on dead phone boards with damaged BGA joints
  • Rework on hang on logo boards where chip joints need replacing
  • Rebuilding the ball array on BGA254 package parts
  • Repeat reballing jobs in a workshop with a reusable steel template

Compatible Devices

  • Chip-level compatibility with Spreadtrum SC-series ICs; supported chips and packages listed below
  • SC9863A
  • SC9832E
  • BGA254
  • RPM6743-31
  • SC2721G
  • SR3595D
  • SR3593A
  • RTM7916-51

FAQ

What is the product name?
The product name is Amaoe SU3 BGA Reballing Stencil.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is SU3, also listed as SU-3.
What is this product used for?
This product is used for reballing Spreadtrum ICs by guiding solder balls onto the chip pads after removal from the board.
Which devices are compatible with this product?
This product is compatible with Spreadtrum chips SC9863A, SC9832E, SC2721G, SR3595D, SR3593A, RPM6743-31, RTM7916-51 and the BGA254 package.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Spreadtrum chips does the SU3 stencil cover, and how does it differ from SU1 and SU2?
The SU3 covers SC9863A, SC9832E, BGA254, RPM6743-31, SC2721G, SR3595D, SR3593A and RTM7916-51. The SU1 targets SC7730, SC7731, SC8830, SC9830, SC8825 and SC7715 parts, and the SU2 targets SC651E, SC9850, SC6820, SC9820A, SC6500D, SC6533G and SC6531DA.
What thickness and hole type does the SU3 stencil use?
The SU3 stencil measures 0.12mm thick, uses square holes, and comes in Japanese steel sheet that resists deformation and works for repeated use.