Magma C210-K Blade Soldering Tip for T210 & T26 Handles
₨ 1
C210 Blade Soldering Tip for Mobile Board Repair
The Magma C210-K is a C210 blade soldering tip for technicians who tin pads, clear bridges, and drag solder across fine-pitch SMD rows. The knife profile gives you a wide contact edge, and the integrated heating element keeps heat at the point of contact. It fits T210 and T26 style handles on the 210 standard, so you swap it in without changing your station. Use it on charging port pads, ground planes, and IC pad cleanup during daily mobile repair work in Pakistan. Match it only with 210-series handles, because C245 and C115 handles take different cartridges.
Out of stock
C210 Blade Soldering Tip Built for Drag Soldering and Pad Work
The Magma C210-K is a C210 blade soldering tip, a knife-profile cartridge from Magma’s 210 series. The heating element sits inside the tip, so the blade reaches working temperature quickly and the heat stays where the solder flows. If you run a T210 or T26 style handle on your repair bench, this tip gives you a wide, flat contact edge instead of a single point. That edge matters when you drag solder across a row of fine-pitch pads, clear a solder bridge, or flood a ground pad that a conical tip heats too slowly. Mechanicpk stocks it for technicians who want a dependable consumable tip for daily board-level work.
Why the Knife Profile Changes Your Soldering Technique
A blade tip spreads heat along an edge instead of a single point. When you drag the edge across a row of SMD pads, the solder follows the blade and leaves each pad evenly tinned. A conical tip forces you to dab pad by pad, which wastes time on a dead phone with a damaged connector footprint and raises the risk of lifting a pad. The knife profile also clears solder bridges between fine-pitch pins in one pass: you wet the bridge, slide the edge through, and the excess solder travels with the blade. Large ground and shield pads pull heat away from small tips, but the wider contact surface warms them faster. If you currently swap between a fine tip and a chisel tip several times per board, one blade cartridge covers a good share of those jobs.
Cartridge Construction and Handle Matching
The C210 standard places the heating element inside the tip, so heat travels a short path to the solder. Magma builds the C210-K with a stainless steel housing that reduces heat loss, a plating and soldering layer that prevents tin climbing, and a nickel coating that resists rust and corrosion. Handle matching decides whether the tip works at all. A 210 handle accepts only a 210 tip, so a C245 or C115 handle rejects this cartridge. Magma also states the tip must sit fully inside the handle to work properly, so push it home before you power the station. Your station controls the temperature, so set it for your solder alloy and let the cartridge hold it. Browse the Soldering Stations category at Mechanicpk to pair a compatible station with this tip.
Where It Fits in a Mobile Repair Workflow
Most technicians reach for this tip right after the hot air gun finishes its job. You lift a damaged IC, and the pads underneath hold leftover solder in uneven lumps. The blade levels those pads before you reball or place a new chip, which makes every IC change karna job cleaner. On a charging issue, the blade tins the pads around a worn charging port so the new connector seats flat. When you trace a hardware fault, the fine edge lets you solder a jumper wire to a test point, which is how jumper lagana works on a dead board. Pair the tip with a microscope for pad inspection, a PCB holder to keep the board still, and a multimeter to check continuity once the solder cools. Technicians who order Hot Air Stations and Reballing Kits from Mechanicpk usually add this blade tip to the same order, because it handles the pad preparation that sits between those two steps.
| Weight | 0.5 kg |
|---|
Key Features
- ✓C210 standard cartridge for T210 and T26 style handles
- ✓Integrated heating element inside the tip
- ✓Knife (blade) profile with a wide contact edge
- ✓Drag soldering across dense SMD pad rows
- ✓Stainless steel housing to reduce heat loss
- ✓Plating and soldering layer to prevent tin climbing
- ✓Nickel coating for rust and corrosion resistance
- ✓Replaceable cartridge, so you swap the tip without replacing the handle
Specifications
| Brand | Magma |
|---|---|
| Model | C210-K |
| Category | Soldering Iron Tips |
| Compatibility | T210 and T26 style soldering handles (C210 standard) |
| Technology | C210 cartridge with integrated heating element, knife (blade) profile |
| Material | Stainless steel housing with nickel coating |
Common Repair Uses
- ✓Pad tinning, drag soldering, and rework cleanup on mobile phone motherboards
- ✓Drag soldering across fine-pitch SMD pad rows
- ✓Clearing solder bridges between adjacent pins
- ✓Tinning large ground and shield pads
- ✓Cleaning leftover solder from pads after IC removal
- ✓Preparing pads before reballing or chip placement
- ✓Tinning charging port pads during connector replacement
- ✓Soldering jumper wires and flying leads to test points
- ✓Small module and consumer electronics board service
Compatible Devices
- ✓Universal soldering tip for 210-series handles — not phone-specific, works on any board your station can reach
- ✓T210 precision handles
- ✓T26 style soldering handles
- ✓JBC T210-A handpiece
- ✓JBC T210-PA handpiece
- ✓Sugon T26D soldering station handle
- ✓Aifen 210-series handles
- ✓Aixun 210-series handles
- ✓Any soldering station handle built for the C210 standard



