Mechanic MR6 Air Double Bearing PCB Repair Fixture
₨ 3,200
MR6 Air Double Bearing Motherboard Fixture
The Mechanic MR6 Air PCB holder fixture locks a phone motherboard in place while you work at the hot air station. Its dual-axis spiral clamp runs on double bearings, so the jaws close firm and the board stays put. Multiple misalignment buckles and several card positions let you set boards of different shapes. The fixture also holds a CPU, a hard disk component, or another precision IC during glue removal. Use it for chip removal, motherboard soldering, and board maintenance on your repair bench.
In stock
MR6 Air PCB Holder Fixture for Stable Board-Level Rework
The MR6 Air PCB holder fixture from Mechanic gives your bench a rigid, adjustable grip on a phone motherboard while you work with hot air and a soldering iron. Mechanic builds it around a double-bearing, dual-axis spiral clamp, so you tighten and slide the jaws smoothly and the board stays where you place it. A dead phone or a hardware fault that needs an IC change karna job punishes a loose board with lifted pads, and this fixture removes that risk before you heat anything.
How the Double-Bearing Dual-Axis Clamp Holds Your Board
The MR6 Air clamps through a dual-axis spiral design on double bearings. You turn the screws, the jaws travel smoothly along both axes, and the grip locks firm instead of creeping loose. That matters when you hold a board over a hot air station for several minutes and cannot afford a shift.
Mechanic also fits the fixture with multiple misalignment buckles and a range of card positions. You choose the position that matches the outline of the board in front of you, so one fixture covers motherboards of different shapes instead of forcing you to keep a separate jig for every layout. Mechanic positions the MR6 Air as a high-temperature holder for rework duty, which suits chip removal and board maintenance jobs where heat reaches the clamp zone.
Holding CPUs and ICs for Glue Removal
Many technicians treat a PCB holder as a motherboard-only accessory. The MR6 Air does more. Mechanic specifies that the fixture also clamps a CPU, a hard disk component, or another precision IC that needs degumming. When you strip glue from an IC before reballing, a steady grip keeps your scraper and tweezers controlled and keeps your fingers away from the hot surface.
The fixture also frees both hands. One hand runs the hot air gun or soldering iron while the other works the tool that lifts the chip. Pair it with a microscope and you focus on one spot without chasing a moving board across the bench.
Where the MR6 Air Fits in Your Repair Workflow
Board-level repair starts with diagnosis, usually with a multimeter, and moves to heat and rework once you find the fault. A charging issue, a hang on logo problem, or a dead phone often ends at that stage. The MR6 Air sits between those two steps. You clamp the board, bring in your hot air station or soldering station, remove or replace the chip, and clean the pads before you reball or reflow.
Because the fixture adjusts across board shapes, it suits a workshop that sees many brands in a single day. You reset the buckle position, tighten the clamp, and start the next job without swapping tools. A service center that runs several benches can equip each one with a dedicated holder and keep rework consistent between technicians.
If your repair volume grows, you can build the same station around other PCB holders, reballing kits, and microscopes from the Mechanicpk catalog. The MR6 Air remains the entry point for technicians who want a double-bearing, biaxial clamp with multiple board positions for everyday motherboard soldering and IC work.
| Weight | 0.4 kg |
|---|
Key Features
- ✓Dual-axis spiral clamp design
- ✓Double-bearing mechanism for smooth jaw movement
- ✓Firm, stable clamping that resists loosening
- ✓Multiple misalignment buckles
- ✓Several card positions for different board shapes
- ✓Positioned as a high-temperature holder for rework
- ✓Holds CPUs, hard disk components, and precision ICs
- ✓Supports glue removal and chip removal workflows
Specifications
| Brand | Mechanic |
|---|---|
| Model | MR6 Air |
| Category | PCB Holder / Motherboard Repair Fixture |
| Compatibility | Universal — mobile phone motherboards of varied shapes |
| Technology | Double-bearing, dual-axis (biaxial) spiral clamp |
Common Repair Uses
- ✓Board holding during heat-based repair and glue removal
- ✓Motherboard soldering
- ✓Chip removal with a hot air station
- ✓Board maintenance and rework
- ✓Glue removal from CPUs and precision ICs
- ✓Holding the board steady under a microscope
- ✓Preparing ICs and pads before reballing
- ✓Securing the PCB during IC change jobs
Compatible Devices
- ✓Universal — not device-specific; fits mobile phone motherboards of varied shapes through multiple card positions
- ✓Mobile phone motherboards of different shapes
- ✓Bare PCBs held for soldering and chip removal
- ✓CPU packages that need glue removal
- ✓Hard disk components that need degumming
- ✓Other precision ICs that need degumming
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the MR6 Air hold boards of different shapes and sizes?
Can I clamp a CPU or IC for glue removal, not only a full motherboard?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock



