MiJing MJ-190A Solder Paste 35g Lead-Free

₨ 1

MiJing MJ-190A 35g Lead-Free Solder Paste

The MiJing MJ-190A is a 35 g lead-free, halogen-free solder paste rated for medium-temperature work at about 190°C. It suits BGA ball placement, CPU IC reattachment, and SMD rework on mobile phone motherboards and computer boards. The no-clean flux keeps your post-reflow workflow short, and the vendor describes the paste as reusable across several jobs. Use it with a stencil or a reballing fixture to place tin precisely on your chip pads.

Out of stock

12 People watching this product now!
Description

MiJing MJ-190A Solder Paste for BGA and Medium-Temperature Rework

The MiJing MJ-190A is a 35 g lead-free solder paste built for medium-temperature work on mobile phone and computer boards. Its listed working point sits near 190°C, which places it in the middle of the MiJing range, between the 158 and 217 options. You reach for this paste when a CPU IC, a BGA chip, or an SMD part needs fresh tin during rework. The formulation pairs a halogen-free flux with a no-clean residue, so the joint stays tidy through reflow. For a technician who already runs a hot air station and a stencil, this paste fits the existing bench routine without new tools. Choose it when your job calls for a medium-temperature profile rather than a low-temperature alloy or a higher-temperature one, and when you want a single paste that covers both ball placement and component rework.

Matching the 190°C Profile to Your Repair Job

MiJing describes the MJ-190A as a medium-temperature paste, and the working point of about 190 degrees sets your starting profile. Your hot air station should bring the joint into that zone evenly, without pushing the chip beyond what the board can take. Set the nozzle size and airflow before you lift the board, then watch the tin melt across each pad before you withdraw the heat. Technicians who run both low- and medium-temperature pastes keep their settings separate, so every job begins from a known profile. A repeatable profile gives you cleaner balls, fewer rework cycles, and less stress on heat-sensitive components near the chip. Log the temperature and nozzle setting you used for each board, because that record speeds up your next repair of the same model.

Lead-Free and Halogen-Free Formulation

The MJ-190A is lead-free and halogen-free, which matters when you handle boards that must meet material rules or leave your shop for export. The no-clean flux leaves a residue that most rework jobs do not require you to wash away. Clean the board anyway when you inspect joints under a microscope, because residue can hide a bridge on fine-pitch pads. The paste holds its shape on a stencil and inside a reballing fixture, which keeps the tin volume on each pad consistent from chip to chip. The vendor describes the paste as reusable, so keep the tub closed between sessions and keep your spatula clean to protect the remaining paste. Pair the paste with a fine-tip applicator when you work on small SMD points, since a steady hand gives you more control than a broad spatula on tight layouts.

Ball Placement and SMD Rework on Mobile and Computer Boards

The listing names two main workflows: ball placement for computer and mobile chips, and rework on PCB and SMD components. For BGA reballing, you spread the paste through a stencil, seat the chip in its fixture, and reflow it under your hot air station. Match the stencil opening to the ball diameter before you start, because a mismatch leaves you with missing or doubled balls. On a CPU IC, the same paste helps you reattach a part that lifted during desoldering, which can save a board you would otherwise scrap. Use the paste sparingly, since excess tin bridges neighboring pads on fine-pitch chips. After reflow, let the board cool before you handle it, and check the balls under magnification before you remount the chip on the motherboard. Careful alignment at this stage prevents most of the callbacks you would otherwise face on a reworked board.

Additional information
Weight0.35 kg
Q & A
Please login to post questions

Key Features

  • Lead-free and halogen-free formulation
  • Medium-temperature working point at about 190°C
  • No-clean flux that leaves minimal residue
  • 35 g net content
  • Suitable for BGA ball placement with a stencil or fixture
  • Suitable for SMD and PCB rework
  • Vendor describes the paste as reusable across several jobs
  • Works with a standard hot air station profile

Specifications

BrandMiJing
ModelMJ-190A
CategorySolder Paste
CompatibilityUniversal, not device-specific
TechnologyLead-free, halogen-free, no-clean flux, medium-temperature (approx. 190°C working point)
Weight35 g (net content)

Common Repair Uses

  • BGA reballing with a stencil or reballing fixture
  • Ball placement on computer and mobile chips
  • Reattaching CPU ICs after desoldering
  • SMD component rework on mobile phone PCBs
  • PCB rework on computer boards

Compatible Devices

  • Verified scope is general, not device-specific
  • Mobile phone motherboard CPU ICs
  • Mobile phone BGA chips
  • SMD components on mobile phone PCBs
  • Computer chips for ball placement

FAQ

What is the product name?
The product name is MiJing MJ-190A Solder Paste 35g.
What is the brand of this product?
The brand of this product is MiJing.
What is the model of this product?
The model of this product is MJ-190A.
What is this product used for?
This product is used for BGA ball placement, CPU IC reattachment, and SMD rework.
Which devices are compatible with this product?
This product is compatible with mobile phone motherboard CPU ICs, BGA chips, and SMD components, and is not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the MJ-190A lead-free?
Yes, the listing describes the MJ-190A as lead-free and halogen-free.
What temperature does the MJ-190A suit?
The MJ-190A is a medium-temperature paste with a listed working point of about 190°C.