AiXun 2nd Gen Chip Grinding Machine for Touch IC & CPU
₨ 1
AiXun 2nd Gen Chip Grinding Machine for Touch IC and CPU Work
The AiXun 2nd Gen chip grinding machine removes touch ICs, NAND flash chips, and CPUs from a motherboard by milling instead of applying hot air. It reaches a maximum no-load speed of 24,000 rpm, and its 0.8-inch OLED screen shows the live rotation speed while you work. You set the cut length with a stop block and mount the grinding head on the included universal mold. The compact body suits a busy repair bench where you need controlled, heat-free chip removal before reballing or replacing a component.
Out of stock
AiXun 2nd Gen Chip Grinding Machine: Mechanical Chip Removal for Motherboard Repair
Heat-based chip removal carries a cost on a crowded logic board. A hot air station raises the temperature of the components around the target chip, and the solder under neighboring parts can soften or shift. The AiXun 2nd Gen chip grinding machine takes a mechanical route instead. You mill the chip down until its connection to the board weakens, which keeps prolonged heat away from the rest of the motherboard. Technicians working on touch ICs, NAND flash, and CPUs use it as a controlled grinding step before reballing, reflow, or chip replacement. This page explains where the machine fits in your repair sequence, how its speed and travel controls work, and what the universal mold covers.
Where the Grinder Fits in Your Repair Workflow
A grinding step only makes sense when it belongs to a clear repair sequence. Start with diagnostics on your board tester, identify the faulty chip, and confirm which pads and nearby components you need to protect. Grind the chip until it releases, then clean the pad area and inspect it under a microscope. From there, you either reball and reinstall the original chip or fit a replacement. Mechanical removal also suits boards where earlier heat work has already stressed the solder mask or nearby traces, because you add no further thermal load. Keep your reballing kit and hot air station close at hand, since grinding rarely finishes the job alone.
Speed Control and the OLED Rotation Display
The machine reaches a maximum no-load speed of 24,000 rpm. Load reduces the actual speed, so the value during an idle spin differs from the speed at the head once you press into a chip. The 0.8-inch OLED screen shows the rotation speed at any time, which gives you a live reference during each session. Read the display before you start and confirm it matches the task. A lower speed suits a cautious first pass on a fragile board, while a higher speed helps when the chip material resists grinding. Watch the screen throughout the cut instead of relying only on how the handle feels.
Stop Block, Travel Length, and Grinding Heads
Travel length controls how far the head moves across the work area. The stop block lets you fix that distance, so each pass ends at the same point and you avoid grinding past the chip edge into the PCB. Setting the stop block before you start protects neighboring pads and saves correction work later. The package includes two grinding heads, so you keep a spare ready when one wears. Inspect each head before mounting, because a worn head grinds unevenly. Uneven grinding causes more board damage than a slower, careful pass does, so replace a head before it starts to drift.
Universal Mold and Chip Coverage
The universal mold lets this machine handle several chip families without a dedicated jig for every model. Its scope is universal rather than device-specific, so fit depends on the chip size and the board layout you work with. Touch ICs, NAND flash chips, and CPUs fall within the intended application set, and the machine also covers motherboard chips and camera-area components on mobile boards. Before you grind, verify the chip footprint and the clearance around it, then confirm the mold sits square. Clean the work area after each job, because grinding dust can settle on nearby components and cause confusion during reassembly.
| Weight | 2.0 kg |
|---|
Key Features
- ✓Mechanical chip removal without heat
- ✓Maximum no-load speed of 24,000 rpm
- ✓0.8-inch OLED screen showing live rotation speed
- ✓Adjustable travel length via stop block
- ✓Universal mold for multiple chip families
- ✓Two grinding heads included in the package
- ✓Compact, lightweight body for bench work
- ✓Built for touch IC, NAND, and CPU grinding
Specifications
| Brand | AiXun |
|---|---|
| Model | AiXun 2nd Gen |
| Category | Mobile Repair Tools |
| Compatibility | Universal, not device-specific |
| Supported Devices | Mobile touch ICs, NAND flash chips, CPUs, motherboard chips |
| Technology | Mechanical chip grinding with 24,000 rpm maximum no-load speed and OLED rotation display |
Common Repair Uses
- ✓Removing a faulty touch IC before replacing it on a dead-touch board
- ✓Grinding off a NAND flash chip before reballing and reinstalling it
- ✓Taking off a CPU chip for reballing or replacement
- ✓Clearing old solder and chip residue from pads before fitting a new component
- ✓Removing a heat-damaged chip without adding more thermal stress to nearby parts
- ✓Preparing a board for an IC change karna job on a multi-layer PCB
- ✓Grinding camera-area chips during board-level repair
- ✓Controlling cut depth with the stop block on boards with tight component spacing
Compatible Devices
- ✓Universal, not device-specific. Scope is set by the universal mold and chip footprint.
- ✓Mobile phone touch IC chips on logic boards
- ✓NAND flash chips on mobile motherboards
- ✓Mobile phone CPU chips
- ✓Motherboard chips on mobile phone PCBs
- ✓Camera-area components on mobile boards
- ✓Chips requiring mechanical removal before reballing
- ✓Chip footprints that fit the universal mold
- ✓Mobile phone PCBs across multiple chip families
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can this grinder remove a chip without heat damage to the board?
What rotation speed does the AiXun 2nd Gen grinder run at?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



