Qianli QS67 Qualcomm PM Series 2 Bumblebee Stencil
₨ 600
Qianli QS67 PM Series 2 Stencil
The Qianli Bumblebee QS67 is a Qualcomm PM Series 2 stencil for reballing power management ICs on Android boards. One mesh covers 17 PM and PMI part numbers, including PM8953, PM8916, PM8996, PM8941 and PMI8996. Square holes with rounded corners help solder balls seat cleanly on the pads, and the mesh is built to stay precise and durable over time. Pair it with a hot air station and a reballing kit to rebuild a lifted or replaced PMIC after a charging issue, a dead phone, or a short on the main power rail.
In stock
Qualcomm PM Series 2 Stencil for PMIC Reballing
The Qualcomm PM Series 2 stencil from Qianli, model QS67, puts a long list of Qualcomm power management ICs on one Bumblebee mesh. Mechanicpk lists it for technicians who rebuild PMICs at chip level instead of condemning the whole board. Qualcomm PMICs sit on the main board beside the CPU and regulate the voltage rails every other component depends on, so a failed one shows up as a charging issue, a dead phone, or a board that draws current without booting. The mesh uses square holes with rounded corners, a layout Qianli designs for BGA work, and the maker builds it to stay precise and durable over time. When you hold a dead phone with a power IC already lifted, this stencil takes you from bare pads to fresh balls without hunting for a separate template per part number.
PMIC Coverage You Can Verify Before You Order
The QS67 covers PM8841, PM8909, PM8110, PM8004, PM8019, PM8018, PM8926, PM8996, PMI8996, PM8956, PM8941, PM8953, PM8917, PM8921, PM8922, PM8916 and PM8058. That makes 17 Qualcomm part numbers across the PM and PMI families on a single stencil, including the PMI8996 companion IC alongside the PM8996. Read the marking on your target IC and match it against this list before you buy, because Qualcomm reuses the PM prefix across many generations and the QS67 does not reach all of them. Qianli sells a separate PM Series 1 stencil, the QS66, and covers newer parts such as the PM660 family with other models, so match the exact marking rather than the prefix.
Where It Fits in Your PMIC Rework Workflow
Power IC work follows a fixed sequence on the bench, and the stencil sits in the middle of it. You confirm the fault first. Use your multimeter to check for a short on the battery or VBUS line, then compare against a known good board. Once the PMIC is the suspect, you heat the board on a hot air station, lift the IC, and clean the pads under a microscope. A PCB holder keeps the board still while you work. Next you align the QS67 over the IC, press the solder balls through the holes, and reflow so each ball seats on its pad. Fix the stencil in place with heat-resistant tape or a stencil holder so it does not drift while the balls settle, and let the board cool before you lift the stencil. A shifted stencil leaves bridged or missing balls, and you repeat the job. After a final inspection you place the IC back and solder it down. This is the IC change karna routine for charging issue, dead phone, and hang on logo cases that trace back to a power rail hardware fault.
Choosing the Right Stencil for the Job
Match the stencil to the IC, not to the phone model. The QS67 works as a universal PMIC stencil, so it does not tie to one handset brand. That helps in a shop that sees mixed Android traffic, because you reach for one tool across several boards that carry the listed parts. Check the ball size and pad pitch under your microscope before you commit, since a stencil only helps when its apertures line up with the pads on your IC. Pair it with a reballing kit for balls, flux and a stencil holder, and keep your soldering station nearby for pad cleanup. If your queue also includes CPU or eMMC reballing, those jobs need their own stencils, since the QS67 covers only the PM and PMI parts above. Keep the mesh flat, wipe it with flux remover after each use, and store it away from bends so it keeps its shape. Move up from a single stencil to a full reballing kit when your volume grows past occasional PMIC jobs. The package contains one stencil.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Covers 17 Qualcomm PM and PMI part numbers on one stencil
- ✓Part of the Qianli Bumblebee range
- ✓Square holes with rounded corners for BGA ball placement
- ✓Built to stay precise and durable over time
- ✓Newer material and surface treatment for easier, more accurate use
- ✓Universal design, not tied to a single phone brand
- ✓Suits PMIC reballing with hot air stations and reballing kits
- ✓Single-stencil pack for focused PM Series 2 work
Specifications
| Brand | Qianli |
|---|---|
| Model | QS67 |
| Category | BGA Reballing Stencil (Bumblebee Series) |
| Compatibility | Qualcomm PM / PMI power management ICs (PM Series 2); universal, not handset-specific |
| Supported Devices | Android boards carrying the listed Qualcomm PM / PMI ICs |
| Technology | Square holes with rounded corners (BGA stencil) |
| Package Contents | 1 x Stencil |
Common Repair Uses
- ✓Chip-level power IC repair on Qualcomm-based Android boards:
- ✓PMIC reballing after IC removal
- ✓Replacing a faulty power IC (IC change karna)
- ✓Charging issue repair traced to the PMIC
- ✓Dead phone with a short on the main power rail
- ✓Hang on logo cases linked to a power IC fault
- ✓Reballing a reused PMIC after pad cleaning
- ✓Hardware fault diagnosis follow-up after multimeter short checks
- ✓Training bench practice on BGA power IC rework
Compatible Devices
- ✓Universal PMIC stencil, matched by IC marking rather than by phone model. Verified supported Qualcomm ICs:
- ✓PM8841, PM8941
- ✓PM8909, PM8916
- ✓PM8953, PM8956
- ✓PM8996, PMI8996
- ✓PM8917, PM8921, PM8922
- ✓PM8110, PM8926
- ✓PM8004, PM8018, PM8019
- ✓PM8058
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which Qualcomm PMIC chips does the QS67 stencil support?
What is the difference between QS66 and QS67 for Qualcomm PM ICs?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock


