RL-2020 Desoldering Wick 2.0mm x 2.0M by Relife

₨ 850

RL-2020 Desoldering Wick: 2.0mm Copper Braid for Clean Pad Work

The Relife RL-2020 is a 2.0mm copper desoldering wick, 2.0 meters long, made from 100% copper braid. Its fine weave pulls molten solder away from pads, pins and jumpers through capillary action, so you can clear excess tin without overheating the board. The no-clean formulation is halide-free and non-conductive, so the residue can stay on the board after your work. A thumb-wheel dispenser with a sealed housing keeps the wire protected between jobs. Use this wick for SMD pads, connector pins and BGA cleanup on your repair bench.

In stock

11 People watching this product now!
Description

RL-2020 Desoldering Wick for Precise 2.0mm Pad Cleanup

Every repair bench needs a dependable RL-2020 desoldering wick for the moment when one extra blob of solder bridges two pads. The RL-2020 is Relife’s 2.0mm option in its no-clean line, sold as a 2.0 meter length of pure copper braid. Its fine weave draws molten solder upward through capillary action, so you clear pads without dragging the joint apart. Technicians working on SMD layouts, connector rows and BGA fields often keep a mid-width wick like this one within reach, because it covers many common pad sizes. Think of it as the consumable between your iron and your board, doing the heavy lifting so only the solder the joint needs remains. Knowing where it belongs in your workflow makes every roll go further.

Where the 2.0mm Width Fits in Your Repair Workflow

Desoldering usually comes early in a board-level job, before you lift a faulty component or prepare a pad for a replacement chip. Many smartphone boards and connector footprints suit a 2.0mm braid, because the width matches a wide range of mid-sized pads. When a dead phone shows shorts across several pins, you strip solder from each pin in turn, then check continuity before you move on. After a component change, a clean and level surface gives the new part a proper seat for reflow. Choose a narrower wick for fine-pitch work and a wider one for larger pads, then keep the 2.0mm version ready for everything in between. That middle position makes it a practical everyday wick on a busy bench.

Copper Braid, Flux Behaviour and Residue

The braid is 100% copper, and the fine weave supports strong capillary action when you press it onto molten solder. The flux in this no-clean formulation is halide-free, and Relife describes the leftover residue as non-conductive. You do not need to scrub the board after every job, which saves time when you run several repairs back to back. Relife claims this series removes solder faster than conventional wicks based on Type-R flux, so you spend less time heating each pad. Hold the iron firmly on the braid, lift the wick once the solder flows, and cut off the used section before the next pass. A clean working end gives you consistent results across the whole roll.

Dispenser Design and Storage

The wick ships on a thumb-wheel dispenser, which lets you feed out braid in short, controlled lengths with one hand. The sealed housing protects the wire from moisture, which supports a longer working life on a shared bench. A stainless steel mouth guides the braid onto the joint, keeping the wire aligned while the iron does its work. Store the dispenser in a dry drawer away from humid areas, and keep it apart from sharp tools that could damage the wheel. Keep the mouth clear of solder debris so the braid feeds smoothly every time. Good storage turns a practical wick into a dependable one on your bench.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • 2.0mm width and 2.0 meter length
  • 100% copper braid construction
  • No-clean, low-residue formulation
  • Halide-free, non-conductive residue
  • Fine weave for strong capillary action
  • Thumb-wheel dispenser for one-hand feeding
  • Sealed dispenser protects the wire from moisture
  • Stainless steel mouth guides the braid onto the joint

Specifications

BrandRELIFE
ModelRL-2020
CategoryDesoldering Wick
CompatibilityUniversal, not device-specific
TechnologyNo-clean, halide-free flux
Material100% copper
Width2.0mm
Length2.0m

Common Repair Uses

  • Clearing solder bridges between IC pins after rework
  • Removing excess solder from pads before fitting a new component
  • Stripping solder from a shorted IC during dead phone diagnosis
  • Flattening BGA pads ahead of reballing
  • Cleaning connector pins before replacing a charging port or flex connector
  • Removing old solder from a component lifted off a board
  • Preparing a pad for jumper lagana or re-tinning
  • Clearing solder from small board repairs on PCBs

Compatible Devices

  • Universal, not device-specific. Scope covers any solder joint within reach of a 2.0mm braid.
  • Universal, not device-specific: general PCB solder joints
  • SMD pads on mobile and PC boards
  • BGA pads on IC packages (Relife lists BGA wicks in its range)
  • Connector pins and solder joints
  • General PCB pads on phone and PC boards
  • Jumper and bridge clean-up points
  • Board pads before a replacement component is fitted
  • Not verified for any single phone model or chipset

FAQ

What is the product name?
The product name is Relife RL-2020 Desoldering Wick 2.0mm x 2.0M.
What is the brand of this product?
The brand of this product is RELIFE.
What is the model of this product?
The model of this product is RL-2020.
What is this product used for?
This product is used for removing excess solder from pads, pins and joints during repair and rework.
Which devices are compatible with this product?
This product is compatible with universal PCB solder joints, including SMD pads and BGA pads, and is not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the RL-2020 leave residue that must be cleaned?
The manufacturer describes the residue as halide-free and non-conductive, so the board does not need cleaning after normal use.
Which wick width should I choose for BGA and SMD work?
The RL-2020 is the 2.0mm option in Relife’s range, which also includes 1.5mm, 2.5mm, 3.0mm and 3.5mm widths, so match the width to your pad size.