RELIFE RL-072 Flux Syringe Booster for 10cc Syringes

₨ 150

RL-072 Flux Syringe Booster for Controlled 10cc Dispensing

The RL-072 is a plastic syringe booster from Relife that fits standard 10cc syringes and gives you a steadier, lighter push when you dispense flux, solder paste, UV mask or structural adhesive. Its push rod carries an exhaust hole that lets trapped air escape behind the plunger, so the flow stays smooth and each drop lands where you aim. Two dispensing needles come in the box, letting you switch between a fine tip for BGA pads and a wider tip for larger joints. Your hand tires less across long board sessions, and the compact body fits easily into a crowded repair setup. You supply the flux, and this booster gives you the control to dose it precisely.

Out of stock

18 People watching this product now!
Description

RL-072 Flux Syringe Booster for Precise Dispensing on Your Repair Bench

Every technician who has pushed a 10cc syringe by hand knows the frustration of uneven pressure, flux that spits onto the board, and a joint that ends up flooded when you needed only a thin film. The RL-072 flux syringe booster from Relife fixes that problem by turning your grip into smooth, measured pressure on standard 10cc syringes. It works with flux, solder paste, UV mask, structural adhesive and the other fluids you dispense daily, so one tool covers several steps on your repair bench. The plastic body stays light and compact, which matters when you work for long hours on a motherboard and your hand starts to tire by the afternoon. You gain control over how much material reaches each pad, and that control shows up as cleaner joints and less waste on expensive solder paste. Whether you clean up a charging issue on a phone or prepare a BGA site for reballing, this booster helps you keep the dose consistent from the first joint to the last.

How the Push Rod Exhaust Hole Reduces Resistance

Air trapped behind the plunger pushes back against every stroke you make, and that resistance turns a simple dispense into a jerky, uneven bead. The RL-072 counters this with an exhaust hole in the push rod, which lets trapped air escape as you press down. The result is a lighter push from the first millimeter, so your thumb controls the flow instead of your wrist fighting the syringe. This difference matters most with thicker materials such as solder paste and rosin, where a stiff push often leads to a surge of material onto the pad. Smooth travel also makes it easier to stop exactly where you want, which keeps the dose consistent across dozens of joints in one session. Once you learn the rhythm, a short, steady press becomes second nature, and your results stop depending on how tired your hand feels that day.

Dispensing Needles for Fine Pads and Tight Spaces

Two dispensing needles come with every RL-072, so you can match the tip to the job without ordering extra parts before your first repair session. A fine needle suits BGA pads and tight SMD rows, where one oversized drop of flux can bridge two contacts and cause a short you then have to chase. A wider needle handles larger solder points and spreads UV mask coverage more evenly across the area you need to protect. Keep one needle per material, so flux residue from a previous job never contaminates the paste or glue you load next. Before you touch the board, press a few drops onto scrap paper to confirm the flow and check that the needle has no blockage. This quick check takes seconds, and it protects a motherboard that might cost you far more time and parts to recover.

Where the RL-072 Fits in Board-Level Repair

Flux plays a role at several stages of board-level work, from desoldering a component to reballing a BGA chip and tinning a pad that has oxidized. A controlled dispense at each stage keeps the flux where it helps the joint and away from the parts that should stay clean. Many charging issue and display problem repairs involve reflowing a small IC, and a neat flux layer helps the solder flow evenly across every pin. Keep the booster beside your hot air station or soldering iron, so you reach for it without breaking your rhythm on a tricky board. Pair the tool with a good microscope and inspect each pad under magnification before you apply heat, because small errors show up quickly at that scale. Over time, you learn the exact push that gives you a clean joint on the boards you repair most, and that routine saves you hours each month.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Push rod exhaust hole reduces air resistance on each stroke
  • Lightweight plastic body for long bench sessions
  • Ergonomic grip for comfortable, steady pressure
  • Two dispensing needles included
  • Works with flux, solder paste, UV mask and structural adhesive
  • Smooth push for controlled, repeatable dosing
  • Compact size fits tight repair setups
  • Suited to BGA, SMD and motherboard repair workflows

Specifications

BrandRELIFE
ModelRL-072
CategorySolder Paste, Rosin & Flux
Compatibility10cc (10ml) syringes
TechnologyPush rod exhaust hole to reduce air resistance
MaterialPlastic
Dimensions36 × 87 × 24 mm

Common Repair Uses

  • Dispensing flux before desoldering a board-level IC
  • Applying flux before reballing a BGA chip
  • Tinning oxidized pads on a motherboard
  • Dispensing solder paste for reflow during charging issue repairs
  • Applying UV mask on a PCB before soldering
  • Placing green oil on a board section during repair
  • Dispensing structural adhesive during component fixation
  • Dispensing rosin onto pads during rework

Compatible Devices

  • Universal, 10cc (10ml) syringe format. Not device-specific.
  • Flux syringes (10cc)
  • Solder paste syringes
  • UV mask syringes
  • Green oil syringes
  • Rosin-based flux syringes
  • Structural adhesive syringes
  • Tin paste syringes
  • Solder oil syringes

FAQ

What is the product name?
The product name is RL-072 Flux Syringe Booster.
What is the brand of this product?
The brand of this product is RELIFE.
What is the model of this product?
The model of this product is RL-072.
What is this product used for?
This product is used for dispensing flux, solder paste, UV mask and structural adhesive from 10cc syringes.
Which devices are compatible with this product?
This product is compatible with 10cc (10ml) dispensing syringes. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the RL-072 work with 10cc syringes?
Yes, the RL-072 supports 10cc (10ml) syringes, the size used for most flux and solder paste syringes.
Are dispensing needles included with the RL-072?
Yes, the package includes two dispensing needles.