Stainless Steel BGA Scraper for Solder Paste Cleanup
₨ 1
Stainless Steel BGA Scraper for Pad Cleaning and Paste Work
This stainless steel BGA scraper gives your repair bench a compact, precise tool for ball grid array chips and motherboard pads. Measuring 12.5 cm with a silver stainless steel body, it handles solder paste scraping, paste spreading during reballing, and removing glue residue left on BGA areas. You can also use it as a pry tool for opening phone shells and LCD assemblies. At about 0.08 kg, it stays light in the hand during long sessions under the microscope. Keep it in your reballing kit next to your other BGA tools for a complete workflow.
Out of stock
Stainless Steel BGA Scraper: Where It Fits Your Reballing Workflow
A stainless steel BGA scraper belongs at the point where your repair moves from desoldering into cleaning and paste work. Every clean reball depends on flat, prepared pads and a controlled layer of solder paste, and this tool gives you direct hands-on control over both. It sits naturally beside your soldering station, hot air station, and microscope, so you can switch between cleanup and placement without rearranging the bench. The 12.5 cm body keeps your fingers clear of the board while you work under magnification, which helps when pad areas are only a few millimeters wide. Its length also gives you reach across larger chips without losing control. Whether you handle IC, CPU, or NAND pads, a stainless steel blade offers the consistent edge that technicians rely on for predictable results. Treat the blade as a precision edge rather than a lever, and let light, controlled strokes do the removing.
Scraping Solder Paste and Preparing Pads
Solder paste scraping is the job this tool handles most directly. After you apply paste through a stencil or spread it across a BGA surface, the excess needs to come off before the next step begins. Draw the flat stainless steel edge across the pads in short, controlled strokes, and check progress under the microscope after every pass. Keep the blade at a shallow angle so you lift the paste rather than pressing it deeper into the pad openings. Work from one side of the chip to the other to keep the pattern even and avoid leaving ridges that trap extra paste. Clean the blade on a dry cloth between passes so old paste does not smear back onto fresh pads. Once the surface looks flat and clear, inspect it before you place the next component, because leftover paste can bridge pads during reflow.
Removing Glue Residue Around BGA Areas
Glue residue around BGA areas often blocks a clean reball, and this scraper gives you a practical way to lift it. The stainless steel blade works on the thin glue layers left after a chip has been removed, so the pads beneath can be seen and cleaned. Move slowly and keep the blade sliding along the surface rather than digging into it. A gentle approach protects the solder mask and nearby traces, which matters far more than working quickly. Ask yourself whether the glue came off cleanly or only moved, since smeared residue will cause problems later. When you finish, inspect the area under magnification for any film that remains before you apply flux or paste. If residue resists light strokes, stop and assess the bond instead of forcing it, because aggressive scraping is where pad damage usually begins.
Prying Phone Shells and LCD Assemblies
The scraper also works as a pry tool when you open phone housings and LCD assemblies. Its steel edge slides into seams and lifts adhesive, so you can keep one steel tool on the bench for several tasks. Start at a corner, apply light pressure, and move along the seam in small increments. Check the seam for hidden clips before you apply force, because most accidental damage happens when a tool meets unexpected resistance. Keep the blade away from flex cables and connectors, since a slip there can cost more time than the opening saves. At about 0.08 kg, the tool stays comfortable through repeated openings and long sessions. Pair it with your usual plastic tools for delicate screen edges, and use the steel blade only where the frame is metal.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Stainless steel construction
- ✓Silver finish
- ✓12.5 cm length
- ✓Approximately 0.08 kg weight
- ✓Scrapes solder paste from BGA pads
- ✓Removes glue residue around BGA areas
- ✓Pry tool for phone shells and LCD assemblies
Specifications
| Material | Stainless steel |
|---|---|
| Color | Silver |
| Length | 12.5 cm |
| Weight | 0.08 kg |
| Compatibility | iPhone and iPad board work, general cell phone opening |
Common Repair Uses
- ✓Scraping solder paste off BGA pads
- ✓Spreading and smoothing solder paste during reballing
- ✓Removing glue residue from BGA areas
- ✓Prying open phone shells and LCD assemblies
Compatible Devices
- ✓iPhone (stated compatibility)
- ✓iPad (stated compatibility)
- ✓General cell phone opening and repair
- ✓BGA chips on mainboards
FAQ
What is the product name?
What material is this product made from?
What is the length and weight of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can this scraper remove glue residue from BGA chips?
Is this scraper suitable for iPhone board repair?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



