SGM41513 Charging IC – 3A Single-Cell Battery Charger

₨ 550

SGM41513 Charging IC for Li-Ion and Li-Polymer Battery Repair

The SGM41513 is a 3A single-cell battery charger with NVDC power path management and I2C control. It accepts a 3.9 V to 13.5 V input and charges through a 1.5 MHz synchronous buck stage, with OTG boost output up to 1.2 A. On your repair bench, it covers charging failures, dead-phone power path checks, and board-level IC replacement. The package is TQFN-4×4-24L, and every specification below comes from the manufacturer’s published data.

14 People watching this product now!
Description

SGM41513 Charging IC: Power Path Control for Repair Benches

The SGM41513 charging IC sits between the input connector and the battery, so a fault here shows up as no charging, slow charging, or a phone that stays dead after a deep discharge. You test VBUS, check the power path, and then decide between a board-level repair and an IC change. Because the device is I2C programmable, its behavior depends on the register setup of the host board, so measure before you replace anything. This part targets smartphones, tablets, and portable systems that use single-cell Li-Ion or Li-polymer batteries. The sections below cover the input range, battery path behavior, and OTG protection features that matter during diagnosis.

3A Single-Cell Battery Charger Input Range

The SGM41513 accepts an operating input voltage from 3.9 V to 13.5 V and withstands up to 22 V sustained. That margin protects the charging stage when an adapter spikes or a 9 V or 12 V fast charging source feeds the board. The charger runs a 1.5 MHz synchronous buck topology, and it reaches 93.8 percent charge efficiency at 1.02 A from a 5 V input. At 2 A from a 9 V input, efficiency measures 89.8 percent, so the part stays efficient under fast charging loads. Input current limit (IINDPM) and VINDPM tracking adjust the source draw, which keeps a weak USB host from collapsing during charging. When you measure VBUS during fault diagnosis, compare the reading against this window before you blame the charger IC.

Battery Path, Instant-On and Ship Mode Behavior

The battery switch uses a 26 mΩ path, which keeps discharge losses low when the phone runs heavy loads from the battery. Instant-on operation lets the system start with no battery or a highly depleted one, so a dead phone can begin charging without waiting for a long pre-charge sequence. Ship mode holds battery leakage at about 2.5 µA, which means a board stored for weeks keeps its charge. Wake-up and full system reset control from the battery FET helps recover a host that locks up after a power event. Battery temperature sensing covers both charge and boost modes, so a faulty NTC circuit stops charging instead of pushing unsafe current into the cell.

I2C Controlled OTG Boost, Protection and Package

In OTG mode, the boost converter delivers up to 1.2 A and reaches 93.5 percent efficiency at 0.5 A and 92.2 percent at 1 A. Hiccup mode overcurrent protection and output short-circuit protection restart the converter automatically, so a shorted reverse-charge port does not burn the power stage. Selectable PFM mode improves light-load efficiency in both buck and boost operation, which helps standby current on the board. The part comes in a TQFN-4×4-24L package, so you need a matching 4×4 footprint and careful reflow when you replace it. Two related variants, SGM41513A and SGM41513D, exist, so check the IC revision marking on the board before you order a replacement. SGMICRO also offers the EVKIT-SGM41513 evaluation kit on request for bench validation.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 3.9 V to 13.5 V operating input range with up to 22 V sustained voltage
  • 3A single-cell charging with 1.5 MHz synchronous buck topology
  • NVDC power path management with instant-on operation
  • I2C programmable input current limit and VINDPM battery tracking
  • OTG boost mode with output up to 1.2 A
  • Hiccup mode overcurrent and output short-circuit protection
  • 26 mΩ battery switch with ship mode leakage near 2.5 µA
  • Battery temperature sensing for charge and boost modes

Specifications

BrandSG Micro (SGMICRO)
ModelSGM41513
CategoryCharging IC (Single-Cell Battery Charger)
CompatibilitySingle-cell Li-Ion and Li-polymer battery charging circuits
Supported DevicesSmartphones, tablets and portable systems
TechnologyI2C controlled, NVDC power path, 1.5 MHz synchronous buck charger
Input Voltage3.9 V to 13.5 V operating, up to 22 V sustained
Power Rating3A charging, OTG boost up to 1.2 A
DimensionsTQFN-4×4-24L package (4 mm × 4 mm)

Common Repair Uses

  • Diagnosing a no-charge fault by checking VBUS against the 3.9 V to 13.5 V window
  • Restoring charging on a dead phone after confirming the charger IC output path
  • Replacing a faulty charger IC on a board after input and battery path tests pass
  • Checking power-on behavior on a deeply depleted battery through instant-on operation
  • Testing ship mode and wake-up recovery on boards that stay off after long storage
  • Verifying battery temperature sensing when charging stops on a healthy input
  • Testing OTG boost output on boards that must supply reverse power to accessories
  • Hot air rework of the TQFN-4×4-24L package during board-level IC change

Compatible Devices

  • Verified scope is board-level, not device-specific
  • Single-cell Li-Ion battery charging circuits
  • Single-cell Li-Polymer battery charging circuits
  • USB standard hosts and USB 2.0 / USB 3.0 compliant input sources
  • High-voltage adapters within the 3.9 V to 13.5 V operating input range
  • Smartphone and tablet power boards with NVDC power path architecture
  • Portable systems with I2C-controlled charging and OTG boost
  • SGM41513A variant boards (verify IC revision marking)
  • SGM41513D variant boards (verify IC revision marking)

FAQ

What is the product name?
The product name is SGM41513 Charging IC.
What is the brand of this product?
The brand of this product is SG Micro (SGMICRO).
What is the model of this product?
The model of this product is SGM41513.
What is this product used for?
This product is used for charging single-cell Li-Ion and Li-polymer batteries and managing the system power path in portable devices.
Which devices are compatible with this product?
This product is compatible with board-level single-cell battery charging circuits in smartphones, tablets, and portable systems, with an input range of 3.9 V to 13.5 V. Who should use this product? | This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What input voltage range does the SGM41513 support?
The SGM41513 supports an operating input range of 3.9 V to 13.5 V and withstands up to 22 V sustained.
Does the SGM41513 support I2C control and OTG boost mode?
Yes The SGM41513 is I2C programmable and supports OTG boost mode with output up to 1.2 A.