Title: Mechanic HK-M Soldering Iron Stand with Sponge

₨ 1

Soldering Iron Stand with Sponge for Mobile Repair Benches

The Mechanic HK-M soldering iron stand gives your repair bench a dedicated resting place for hot irons. A metal base supports a holder ring that accepts irons up to 1 1/8 inches (28.6 mm) in diameter. The base also holds a replacement cleaning sponge, so you can clean the tip between joints without a separate accessory. It suits IC soldering, jumper work, and general board-level rework. Repair shops and technicians can use it across benches that handle everyday soldering tasks.

Out of stock

20 People watching this product now!
Description

Soldering Iron Stand with Sponge for Your Repair Bench

A soldering iron stand with sponge gives your repair bench a dedicated place to park a hot iron between joints. The Mechanic HK-M combines a metal base with a holder ring that accepts irons up to 1 1/8 inches (28.6 mm) in diameter. The base also holds a replacement cleaning sponge, so you can wipe the tip clean without reaching for a separate tray. For technicians working on ICs, jumper wires, and board-level rework, this setup keeps the iron within reach and the tip ready for the next joint. The sections below cover the holder, the sponge, and where the stand fits your bench.

Metal Base and Holder Ring

The HK-M rests on a metal base that anchors the holder ring above it. The ring is sized for irons up to 1 1/8 inches in diameter, which covers standard pencil-style irons and many handle-style irons used across mobile repair. Measure your iron’s barrel or handle before you order, because anything wider than 1 1/8 inches will not seat in the ring. When the iron sits in the ring, its tip stays off the bench surface and clear of your tools, boards, and cables. The metal base also gives you a dependable resting point across long repair sessions, which matters when you set the iron down dozens of times during one job. A stand that stays put means you spend less time readjusting the iron and more time on the joint itself. Route the iron cord behind the stand so it does not pull the iron off balance during work.

Built-in Sponge for Tip Cleaning

Tip cleaning is built into this stand rather than sold as a separate accessory. The base holds a replacement cleaning sponge, so you can wipe off old solder, flux residue, and oxidation between joints without leaving the bench. A clean tip transfers heat more predictably, which makes a difference when you’re soldering fine-pitch pads or small SMD components. Work the tip across the sponge briefly after each joint, then tin it again before moving to the next pad. Regular cleaning also protects the tip itself, since built-up oxide makes it harder to wet with fresh solder. Replace the sponge once it dries out or stops cleaning effectively, because a worn sponge leaves residue behind and slows your workflow. Keeping the sponge close to the stand means you never reach across the bench mid-job, which saves time on repetitive tasks like jumper work and IC changes.

Fitting the Stand into Your Repair Workflow

The stand sits beside your soldering station during board-level work, where the iron goes down and comes back up constantly. You’ll reach for it during IC change, charging port repair, jumper wire work, and general PCB rework. Its compact footprint leaves room for a microscope, a PCB holder, and a test box on the same bench, so the workspace stays organized. Repair shop owners running multiple benches can place one stand at each station to keep irons off the desk and away from cables. A simple habit helps: place the iron in the ring after each joint, clean the tip on the sponge, and pick the iron back up for the next step. For technicians who move between diagnosis, flashing, and rework on the same board, a fixed resting spot keeps the workflow consistent from start to finish. Pair the stand with a hot air station if your bench handles reballing and BGA work, so each tool has a defined place.

Additional information
Weight0.20 kg
Q & A
Please login to post questions

Key Features

  • Metal base for a stable resting point on the bench
  • Holder ring accepts irons up to 1 1/8" (28.6 mm) in diameter
  • Built-in sponge tray in the base for tip cleaning
  • Replacement cleaning sponge included
  • Compact footprint that saves bench space
  • Works with pencil-style and handle-style soldering irons
  • Standalone accessory, usable with any iron within the diameter limit
  • Keeps the iron off the bench surface between joints

Specifications

BrandMECHANIC
ModelHK-M
CategorySoldering Iron Stand
CompatibilitySoldering irons up to 1 1/8" (28.6 mm) diameter
TechnologyBuilt-in tip cleaning sponge
MaterialMetal base

Common Repair Uses

  • Resting the iron between joints during IC removal and installation
  • Cleaning the tip on the built-in sponge during IC soldering
  • Cleaning the tip during desoldering work on board-level repairs
  • Holding the iron during jumper wire work
  • Parking the iron during charging port and connector soldering
  • Holding the iron during general PCB rework and component replacement
  • Keeping the iron secured on a shared repair bench in repair shops
  • Keeping a hot iron away from cables and the bench surface between tasks

Compatible Devices

  • Universal, not device-specific. Scope is soldering irons up to 1 1/8" (28.6 mm) in diameter.
  • Pencil-style soldering irons up to 1 1/8" (28.6 mm) in diameter
  • Handle-style soldering irons up to 1 1/8" (28.6 mm) in diameter
  • Rework station handles within the 1 1/8" (28.6 mm) diameter limit
  • MECHANIC soldering irons within the diameter limit
  • Soldering irons from other brands within the diameter limit
  • Mobile repair soldering pens within the diameter limit
  • Board-level soldering tools within the diameter limit
  • Electronics repair soldering irons within the diameter limit

FAQ

What is the product name?
The product name is Mechanic HK-M Soldering Iron Stand.
What is the brand of this product?
The brand of this product is MECHANIC.
What is the model of this product?
The model of this product is HK-M.
What is this product used for?
This product holds a soldering iron between joints and cleans the tip on its built-in sponge during board-level soldering work.
Which devices are compatible with this product?
This product is compatible with soldering irons up to 1 1/8 inches (28.6 mm) in diameter. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the HK-M include a cleaning sponge?
Yes. The base holds a replacement cleaning sponge, so no separate purchase is needed to start cleaning your tip.
Can the HK-M hold soldering irons from other brands?
Yes. The holder ring accepts any soldering iron up to 1 1/8 inches (28.6 mm) in diameter, so it is not limited to MECHANIC irons.