Mechanic UV Solder Mask Ink Black 10ml

₨ 1

UV Curing Solder Mask Ink Black for PCB Repair

Mechanic UV Curing Solder Mask Ink Black (10ml) is a UV-curable protective coating for PCB repair and rework. Spread it over exposed copper traces, cover the ground around BGA chipset pads, and insulate jumper points. Once exposed to a 365nm UV lamp or sunlight for a few minutes, the ink cures into a layer that protects traces from moisture, corrosion, short circuits, and arcing. Each pack holds 10ml, enough for regular bench repairs on mobile and general electronics boards.

Out of stock

19 People watching this product now!
Description

UV Solder Mask Ink Black for Mobile PCB Repair

UV solder mask ink black gives your repair bench a fast way to restore insulation on a reworked board. When the original solder mask is scraped away during a repair, bare copper stays exposed to moisture and accidental contact. This UV-curable ink closes that gap in minutes. It sits alongside your soldering station, UV lamp, and masking film, and it finishes the job once the copper work is complete.

Where This Mask Fits in Your Repair Workflow

You reach for this ink after the rework stage, once the damaged area is cleaned and the copper is exposed. Place the transparent mask film over the board so the ink lands only where you need it. Cover the exposed ground around BGA chipset pads and any jumper points that must stay clear of contact. Then cure the ink under UV light before you move on to testing. This step gives you a consistent insulation finish on every board you rework.

Application and UV Curing Steps

Apply a small amount of ink with a toothpick or fine tool, then spread it across the target area through the mask film. Keep the rest of the board covered so the ink does not spread onto pads you need to keep clean. Expose the board to a 365nm UV lamp or to direct sunlight for a few minutes until the layer hardens. Thicker deposits need longer exposure, so spread the ink in a thin, even coat. Check that the surface is fully hard before you handle or test the board.

Protection After Curing and Colour Choice

Once cured, the black layer insulates copper traces against short circuits and electrical arcing. It also protects the repaired area from moisture and corrosion, which matters in humid workshop conditions and on boards that return to daily use. The cured ink does not conduct electricity and resists heat. The UVH900 series comes in black, blue, green, red, yellow, and white, so you can pick the colour that suits your repair or your stock.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • UV-curable solder mask ink in black
  • Cures under 365nm UV light or sunlight
  • Insulates PCB traces against short circuits and arcing
  • Protects traces from moisture and corrosion
  • Heat resistant after curing
  • Does not conduct electricity once cured
  • 10ml capacity per pack
  • Works with transparent mask film for controlled application

Specifications

BrandMechanic
ModelUVH900 Series
CategoryPCB Solder Mask Ink
CompatibilityUniversal, not device-specific
TechnologyUV-curable solder mask (365nm UV light or sunlight curing)
MaterialUV-curable acrylic oligomer ink
Capacity10ml
ColourBlack

Common Repair Uses

  • Insulating jumper points after a board repair
  • Covering exposed ground around BGA chipset pads
  • Restoring solder mask where the original mask was removed or damaged
  • Protecting exposed copper traces from moisture and corrosion
  • Preventing short circuits and arcing on reworked boards
  • Isolating component leads you do not want to touch a jumper
  • PCB solder mask restoration after rework
  • Protecting repaired areas on mobile PCBs

Compatible Devices

  • Universal, not device-specific. Verified scope is PCB repair areas, not individual phone models.
  • Mobile phone motherboards and BGA chipset areas
  • Exposed copper traces on reworked PCBs
  • Jumper points on repaired boards
  • Ground areas around BGA chipset pads
  • Repaired laminate where original solder mask was damaged
  • General electronics PCBs in DIY and repair work
  • Reworked component leads you need to keep isolated
  • Restored solder mask on rework boards

FAQ

What is the product name?
The product name is Mechanic UV Solder Mask Ink Black 10ml.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is from the UVH900 series.
What is this product used for?
This product is used to insulate and protect exposed PCB traces during repair and rework.
Which devices are compatible with this product?
This product is universal and not device-specific. It suits PCB repair work on mobile phone motherboards and general electronics boards.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can sunlight cure this UV solder mask?
Yes, the listings state that you can cure the ink under UV light or in sunlight for a few minutes.
Can I use this mask to cover BGA chipset pads?
Yes, the product is used to cover exposed ground around BGA chipset pads during repair.