YCS Anti-Static Dual Head PCB Cleaning Brush Green
₨ 350
Dual Head Anti-Static Motherboard Brush
The YCS anti-static PCB cleaning brush puts two brush heads on one green ergonomic plastic handle. The soft natural bristle head sweeps dust, flux residue and loose debris off phone boards without scratching components. The second head uses a different bristle type, so you switch cleaning tasks by flipping the brush. Anti-static properties protect sensitive parts while you work, and the heat-resistant build holds up at a busy repair bench. Keep it next to your soldering station for board prep before IC change, after rework, or during hardware fault diagnosis.
In stock
Anti-Static PCB Cleaning Brush for Board-Level Repair
The YCS anti-static PCB cleaning brush gives your repair bench one handle with two working ends. The green ergonomic plastic grip keeps the brush steady during close work. One head carries soft natural bristles that lift dust and residue off a motherboard without damaging surface components. The other head carries a different bristle type for a second cleaning task. Anti-static properties protect delicate parts as you brush, which matters on any board you plan to power up afterwards.
Dual-Head Design and Bristle Roles
Each end handles a different job, so you stop hunting for a second tool mid-repair. Use the soft natural bristle head for general surface cleaning. It moves across connectors, shield areas and component gaps without scratching and without shedding hard fibres onto the board. Flip to the opposite head when the soft bristles cannot clear a stubborn spot. Both heads sit on the same compact body, so the brush fits a toolbox, a bench drawer or a technician’s pocket. The shared handle also means one brush covers the cleaning step of most board jobs.
Where It Fits in Your Board-Level Repair Workflow
Clean boards diagnose faster. Dust, flux and grime hide corrosion marks, cracked joints and burnt tracks, and they trap heat around components. Brush the board before you start testing with a multimeter, and again after you finish rework. Use it on a dead phone that arrives with dirt around the charging section, on a charging issue where residue sits near the port, and on any hardware fault that needs a clear view under the microscope. During IC change karna jobs, clean the area before you fit the hot air nozzle, then brush away leftover flux once the new IC sits in place. Reballing kit work and jumper lagana repairs also finish better on a clean board. Mount the board in your PCB holder, wet the soft head with your usual board cleaner, and work in short strokes.
Anti-Static Handling and Bench Safety
Static discharge damages ICs that look perfectly fine, and the damage often shows up later as a boot loop issue or a dead-after-flash complaint. An anti-static brush removes one avoidable risk from your cleaning step. Always power off the phone and disconnect the battery before you brush the board. Keep your hands and bench grounded as you normally do for rework. The heat-resistant build also suits a workflow where you brush the board close to your hot air station or soldering station, as long as you keep the bristles away from direct heat. Repair shops and service centers that clean boards all day get a durable, low-cost brush that earns its place beside the microscope and the soldering station.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Dual-head design with two bristle types on one handle
- ✓Soft natural bristles that clean without damaging electronic parts
- ✓Anti-static properties that protect sensitive components
- ✓Heat-resistant construction
- ✓Ergonomic green plastic handle for a secure grip
- ✓Compact body that fits any toolbox
- ✓Durable build for daily workshop use
- ✓Available in sets of 2, 3, 4 or 5 brushes
Specifications
| Brand | YCS |
|---|---|
| Category | PCB Cleaning Brush / Repair Accessories |
| Compatibility | Universal, general PCB and motherboard cleaning (not device-specific) |
| Technology | Anti-static |
| Material | Plastic handle with natural bristle head |
Common Repair Uses
- ✓Board cleaning and rework preparation in mobile repair workshops
- ✓Dust removal before diagnostics
- ✓Flux residue cleaning after IC change
- ✓Board cleaning before hot air rework
- ✓Post-reballing board cleanup
- ✓Charging section cleaning on dead phone and charging issue repairs
- ✓Cleaning around connectors and ports
- ✓Pre-inspection cleaning under the microscope
- ✓General workshop motherboard maintenance
Compatible Devices
- ✓Universal cleaning tool for mobile phone and electronic boards, not limited to specific models
- ✓Android phone motherboards (all brands)
- ✓iPhone logic boards
- ✓Tablet motherboards
- ✓Laptop and desktop motherboards
- ✓Phone sub-boards and charging boards
- ✓Connectors and board-to-board sockets
- ✓Shield-area and component gaps on repair boards
- ✓General electronic PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is this anti-static PCB cleaning brush safe to use on a phone motherboard with ICs attached?
Can I use this brush to clean flux after an IC change or reballing job?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock



