TAS2-SA Audio IC (TAS2562YFPT) Smart Amplifier

₨ 450

H2: TAS2562 Audio IC for Phone Speaker Repair
The TAS2562 audio IC from Texas Instruments is a mono, digital-input Class-D smart amplifier that technicians read on phone boards as TAS2-SA. You get the TAS2562YFPT variant in a 36-ball DSBGA package with 0.4 mm pitch. It delivers 6.1 W peak into a 4 Ω load at 3.6 V and uses an integrated 11 V Class-H boost with speaker voltage and current sensing. Use it for board-level speaker amplifier replacement when a phone shows no loudspeaker sound, distorted audio or weak volume. Match the TAS2-SA marking on your board before you order.

17 People watching this product now!
Description

H2: TAS2562 Audio IC (TAS2-SA): Boosted Class-D Smart Amplifier for Phone Speaker Circuits
The TAS2562 audio IC is a mono, digital-input Class-D smart amplifier from Texas Instruments, and technicians read it on phone boards as TAS2-SA. You get the TAS2562YFPT variant, a 36-ball DSBGA part that takes digital audio from the application processor over I2S/TDM and drives the loudspeaker through its own 11 V Class-H boost. TI rates it at 6.1 W peak into a 4 Ω load at a 3.6 V battery voltage. When a phone boots, charges and registers on the network but gives no loudspeaker audio, this amplifier sits at the top of your speaker-circuit checklist.

H3: Smart Amp Protection and Digital Interfaces
The chip senses speaker voltage and current in real time, so the phone can push peak output while keeping the loudspeaker inside its safe operating area. A battery-tracking peak voltage limiter with brown-out prevention adjusts headroom across the charge cycle and stops loud peaks from pulling the supply down. Thermal and over-current protection shut the output stage down during faults, and a spread-spectrum low-EMI mode reduces switching noise. On the control side, the TAS2562 accepts I2S/TDM audio with up to eight channels at 32-bit and 96 kHz, supports sample rates from 8 kHz to 192 kHz, and takes its configuration over I2C with four selectable addresses. TI quotes 112.5 dB SNR at 1% THD+N into 8 Ω and under 1 µA battery current in hardware shutdown. These protection features explain why a damaged supply or a failed amplifier produces weak, clipped or silent output instead of a dead phone.

H3: Supply Rails, DSBGA Package and Reballing
Two supplies power the amplifier: VBAT from 2.7 V to 5.5 V for the power stage, and VDD from 1.65 V to 1.95 V for the digital core. Measure both at the chip before you blame the IC. A missing or shorted rail points you upstream to the PMIC or a failed capacitor, not to the amplifier. The package is a 36-ball DSBGA with 0.4 mm pitch, so you need a hot air station with stable airflow control, quality flux, a matching stencil and fresh solder balls. Preheat the board, shield neighboring components and keep ball height consistent so the chip sits flat during reflow. Freehand soldering does not work at this pitch, and an IC change karna job here needs a microscope. Check continuity on the speaker output pins before you close the phone.

H3: Where the TAS2-SA Fits in Your Audio Repair Workflow
Start with the cheap checks. The speaker, flex cable and connector contacts fail more often than the amplifier. Next, inspect the speaker circuit under a microscope for corrosion, because liquid damage and drops are common causes of a dead loudspeaker. Clean the board, confirm VBAT and VDD, then test the amplifier position for shorts in diode mode. If the rails are healthy and the speaker tests good, replace the IC and run a loudspeaker playback and call test. Pair this part with your hot air station, microscope, reballing kit and soldering station from the Mobile Phone ICs and rework categories. For a newer-generation option, TI’s TAS2572 offers 6.6 W and a 13 V boost, but it uses a different pin-out, so it does not drop into a TAS2562 footprint. Always match the TAS2-SA marking on your board before you order.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Original Texas Instruments TAS2562YFPT with TAS2-SA board marking
  • 6.1 W peak output into 4 Ω at 3.6 V
  • Integrated 11 V Class-H boost
  • Speaker voltage and current sense for speaker protection
  • Battery-tracking peak voltage limiter with brown-out prevention
  • I2S/TDM audio input with I2C control and four selectable addresses
  • 36-ball, 0.4 mm pitch DSBGA package
  • Thermal and over-current protection

Specifications

BrandTexas Instruments
ModelTAS2562YFPT (board marking TAS2-SA)
CategoryMobile Phone Audio Amplifier IC
CompatibilityBoards carrying the TAS2-SA marking at the speaker amplifier position
TechnologyDigital-input Class-D smart amplifier, I/V sense, 11 V Class-H boost, 36-ball DSBGA, 0.4 mm pitch
Input VoltageVBAT 2.7 V to 5.5 V, VDD 1.65 V to 1.95 V
Power Rating6.1 W peak (4 Ω, 3.6 V), 5 W (8 Ω, 3.6 V)
Operating Temperature-40 °C to 85 °C

Common Repair Uses

  • Real speaker-circuit workflows for this amplifier.
  • No loudspeaker sound while boot, charging and network work normally
  • Distorted or crackling loudspeaker output
  • Weak loudspeaker volume
  • Speaker circuit damage after liquid exposure
  • Speaker amplifier replacement after a drop
  • BGA reballing and hot air replacement of the amplifier
  • VBAT and VDD rail checks at the amplifier position
  • Post-repair loudspeaker playback and call testing

Compatible Devices

  • Verified scope: boards that carry the TAS2-SA marking (TAS2562YFPT) at the mono speaker amplifier position. This is not a universal part, so confirm the marking on your board.
  • Huawei boards marked TAS2-SA
  • Honor boards marked TAS2-SA
  • Xiaomi boards marked TAS2-SA
  • Redmi boards marked TAS2-SA
  • Mono speaker amplifier position only
  • Not pin-compatible with TAS2572 or TAS2560 footprints

FAQ

What is the product name?
The product name is TAS2-SA Audio IC.
What is the brand of this product?
The brand of this product is Texas Instruments.
What is the model of this product?
The model of this product is TAS2562YFPT, printed on boards as TAS2-SA.
What is this product used for?
This product is used for speaker amplifier replacement on phone boards with no loudspeaker sound, distorted audio or weak volume.
Which devices are compatible with this product?
This product is compatible with Huawei, Honor, Xiaomi and Redmi boards that carry the TAS2-SA marking at the speaker amplifier position.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which supply voltages does the TAS2562 need before I replace it?
The TAS2562 needs VBAT between 2.7 V and 5.5 V and VDD between 1.65 V and 1.95 V. Measure both at the chip first. A missing rail points you to the PMIC or a shorted component upstream.
What package is the TAS2562YFPT and what pitch do I stencil for?
It uses a 36-ball DSBGA package with 0.4 mm pitch, so you need a matching stencil, flux, fresh solder balls and a hot air station with stable airflow control.