Relife RL-3015 Desoldering Wick Wire

₨ 300

H2: Relife RL-3015 Desoldering Wick for Clean Pad Rework

The Relife RL-3015 desoldering wick gives you a fast way to pull excess solder off pads, pins and bridges during board-level repair. Its copper braid draws molten solder away through capillary action, so you clear a joint without forcing the tip into the pad. Use it before you install a replacement IC, jumper or connector, and when a shorted component needs to come off clean. Technicians working on smartphone motherboards, laptop mainboards and general PCB rework will find it a practical addition to any soldering bench.

Out of stock

14 People watching this product now!
Description

H2: Relife RL-3015 Desoldering Wick Wire for Mobile Board Repair

The Relife RL-3015 desoldering wick is a copper braid tool for removing solder from a joint, and it belongs on every repair bench that handles phone and PCB work. When you place the braid over a solder joint and press a hot iron against it, the molten solder climbs into the weave. This clears the pad so the next component sits flat and seats properly. Technicians often reach for a wick when a dead phone shows a short after a component swap, or when a rushed job leaves bridges between IC pins. Removing the old solder first keeps your workflow cleaner than piling extra flux and heat onto it.

H3: How the Braid Works on a Joint

Desoldering wick relies on capillary action, the same force that pulls liquid into a narrow tube. The copper strands form many tiny channels, and molten solder moves into them as the braid heats up. Your iron needs to transfer heat through the braid, so press the tip on top of the wick and wait until the solder flows. Keep the wick flat against the joint and lift it away only after the solder has moved into the weave. Cut off the saturated section and reposition clean braid for the next joint, because a full section stops pulling solder. This method works on through-hole pins and surface-mount pads alike when your iron tip is sized properly.

H3: Choosing the Right Width for the Pad

Braid width should match the joint you are clearing. A narrow braid suits fine SMD pads and IC pins, where a wide strip can lift copper or pull neighbouring pins. A wider braid works better on connector pins, through-hole leads and larger pads that hold more solder. Check the width printed on your reel before you start, because it decides how much solder you remove at once. Keep a spare reel of a different width on the bench so one job does not force a compromise on the next. For most smartphone motherboard work, a narrow to medium braid covers the majority of tasks.

H3: Keeping Pads Safe During Desoldering

Pads on phone boards lift easily when heat stays on too long. Apply moderate temperature and limit contact to a few seconds per joint. Add a small amount of flux before placing the wick, since flux improves flow and reduces tip drag. Lift the iron straight up once the solder moves, so the braid does not tear copper away with it. Let the joint cool on its own rather than blowing on it or forcing it. Following this routine protects both the pad and the trace underneath, which saves the bench from a much harder rework later.

H3: Where This Wick Fits in Your Repair Workflow

Clear the pads with wick before a replacement component goes on, especially after a faulty part has been lifted. After a short is traced and a component is removed, wick removes the leftover solder that would otherwise block a clean reinstall. During charging port or connector replacement, wick helps separate pins that overlap and hold excess solder. A clean finish also reduces thermal stress on neighbouring components. Pair the wick with a microscope and a hot air station when your work calls for more precision. Many shops keep a dedicated wick reel beside the flux and tweezers for these tasks.

Additional information
Weight0.5 kg
Q & A
Please login to post questions

Key Features

  • Copper braid draws molten solder by capillary action
  • Clears solder bridges between closely spaced IC pins
  • Prepares pads before a replacement component goes on
  • Removes excess solder from through-hole leads and connector pins
  • Works with flux for smoother solder flow
  • Helps leave a flat, usable pad after removal
  • Suits smartphone, laptop and general PCB rework
  • Practical consumable for a reliable repair bench

Specifications

BrandRelife
ModelRL-3015
CategoryDesoldering Wick

Common Repair Uses

  • Removing solder bridges between IC pins after a reflow or rushed job
  • Clearing pads before installing a replacement IC
  • Freeing connector pins during charging port replacement
  • Removing a component that caused a short after the fault is traced
  • Cleaning through-hole leads before removing a jack or socket
  • Preparing a board for a jumper or a new surface-mount component
  • Cleaning excess solder after a failed component removal
  • Restoring flat, usable pads before reinstalling a part

Compatible Devices

  • Universal, not device-specific
  • Smartphone motherboards (any model, solder removal only)
  • Laptop and PC mainboards
  • General PCB rework boards
  • Connector pins and charging port pins
  • Through-hole component leads
  • SMD pads and fine IC pins (with correct width)
  • Solder bridges between closely spaced pins

FAQ

What is the product name?
The product name is Relife RL-3015 Desoldering Wick Wire.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is RL-3015.
What is this product used for?
This product is used for removing solder from joints, pads and pins during board repair.
Which devices are compatible with this product?
This product is compatible with universal PCB and mobile repair work, not a specific device.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this wick work with lead-free solder?
Yes, a copper wick removes lead-free solder, though it usually needs more heat and a little extra flux to flow well.
Which wick width suits fine SMD IC pins?
A narrower braid suits fine SMD pins, while a wider braid suits connector pins and through-hole leads. Confirm the width printed on your reel before buying.