Mechanic XGSP80 183°C Solder Paste 60g
₨ 1
Mechanic XGSP80 183°C Solder Paste
The Mechanic XGSP80 is a 60 g tin-lead solder paste built on a Sn63/Pb37 eutectic alloy with a melting point of 183°C. You get a low-temperature joint that reflows predictably on mobile phone and laptop motherboards, which makes it a solid choice for SMD component soldering and BGA reballing. The 60 g container gives you enough volume for regular bench work, so you avoid placing repeat orders for small packs. Its low-residue profile also reduces post-reflow cleaning on most boards. Choose this paste when your workflow calls for a proven leaded alloy with a fixed melting point.
Out of stock
XGSP80 183°C Solder Paste for Precision SMD and BGA Work
The XGSP80 183°C solder paste sits at the center of many board-level repairs on your bench. It handles SMD pad soldering, BGA chip reballing, IC replacement, and general PCB rework. Its fixed 183°C melting point lets you set your hot air or reflow profile with confidence. Each application starts from a stable alloy, so your joints depend on your technique rather than guesswork about the paste itself. This guide explains the alloy, where the paste fits in your workflow, and how to handle it for consistent results.
Eutectic Sn63/Pb37 Composition and Melting Behaviour
The XGSP80 uses a eutectic tin-lead alloy at a 63/37 ratio. A eutectic composition melts at one temperature rather than across a range, so the paste goes from solid to liquid cleanly at 183°C. That single melting point matters when you work on heat-sensitive components. You avoid the slushy stage that wider-range alloys produce, and the solder wets pads quickly once it reaches temperature. Your joints form with a defined fillet shape, which helps when you pull a BGA chip back into alignment. Keep your hot air temperature set just above 183°C at the joint, not at the nozzle, so the flux and alloy activate together and the paste flows evenly across the pad.
Where XGSP80 Fits in Your Repair Workflow
Most technicians reach for this paste at the rework stage, after diagnostics have identified a faulty IC or a cracked joint. Apply a thin layer through a stencil for BGA reballing, or dispense a small amount onto the pads for SMD replacement. Place the component, then heat the board using your preheat and hot air steps until the paste reflows. Lower-temperature alloys like this one reduce thermal stress on nearby components, which helps when you work on dense logic boards. Pair the paste with a reliable flux and a clean stencil, and you will see consistent results on charging ICs, power management ICs, and audio chips. Use a fresh tip and clean pads before application to prevent bridging between fine-pitch points.
Handling, Storage, and Cleaning on Your Bench
Keep the container sealed when you are not using it, and store it in a cool, dry place away from direct sunlight. Solder paste loses tack and flux activity when it dries out or oxidises, so a loose lid shortens its working life. Bring the paste to room temperature before opening it, which prevents moisture from condensing inside the container. Use a clean syringe or spatula, and remove only the amount you need for each job. After reflow, the paste leaves a low residue on most boards. Clean with isopropyl alcohol wherever residue could affect contacts, test points, or board testing. Wash your hands after handling, and work in a ventilated area, because this is a leaded alloy.
| Weight | 0.6 kg |
|---|
Key Features
- ✓Sn63/Pb37 eutectic alloy with a fixed 183°C melting point
- ✓60 g container for regular bench use
- ✓Suitable for SMD soldering and BGA reballing
- ✓Low residue after reflow on most boards
- ✓Smooth flow for clean, defined solder joints
- ✓Works with hot air and reflow profiles set near 183°C
- ✓Reduces post-solder cleaning on most boards
- ✓Leaded paste for tin-lead rework workflows
Specifications
| Brand | Mechanic |
|---|---|
| Model | XGSP80 |
| Category | Solder Paste |
| Compatibility | SMD and BGA soldering and rework on PCBs |
| Supported Devices | Mobile phone and laptop motherboards |
| Technology | Sn63/Pb37 eutectic tin-lead alloy, melting point 183°C |
| Material | Tin-lead alloy with flux |
Common Repair Uses
- ✓BGA reballing of CPU and memory chips
- ✓Replacing faulty SMD ICs on mobile phone boards
- ✓Replacing charging IC and power management IC
- ✓Reflowing lifted or cracked BGA joints
- ✓Soldering SMD components during PCB rework
- ✓Replacing audio IC and logic chips on dead phone boards
- ✓Repairing laptop motherboard BGA chips after heat damage
- ✓Refreshing pads before fitting replacement components
Compatible Devices
- ✓Scope is general SMD and BGA work on mobile phone and laptop motherboards. Not device-specific.
- ✓Mobile phone motherboards (SMD pads and BGA points)
- ✓Laptop motherboards (BGA chips and SMD components)
- ✓SMD IC pads on general PCB rework
- ✓BGA reballing stencils for tin-lead reballing
- ✓Power management and charging IC pads
- ✓Audio and logic IC pads on logic boards
- ✓Mobile phone CPU and memory BGA points
- ✓Fine-pitch SMD components on repair boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is XGSP80 a lead-free solder paste?
Does XGSP80 need cleaning after reflow?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



![Mechanic-Special-Solder-Paste-XGSP80-[60G]-183℃-1 Mechanic Special Solder Paste XGSP80 [60G] 183℃](https://www.mechanicpk.com/wp-content/uploads/2026/10/Mechanic-Special-Solder-Paste-XGSP80-60G-183℃-1.webp)