Mechanic XGSP30 Solder Paste 20g 183°C Sn63/Pb37

₨ 1

XGSP30 183°C Solder Paste for Mobile Repair

The Mechanic XGSP30 solder paste packs a eutectic Sn63/Pb37 alloy into a 20g unit for bench-level SMD and BGA work. The alloy melts at a single point, 183°C, so you get a predictable reflow temperature on mobile motherboards. The smooth paste lets you place controlled deposits on pads, and the no-clean, low-residue formulation keeps board cleanup short. Technicians use it for reballing, SMD replacement, and pad rework on smartphone and tablet PCBs. Mechanicpk supplies the XGSP30 to repair shops and service centers across Pakistan that want a dependable medium-temperature leaded paste.

Out of stock

16 People watching this product now!
Description

Mechanic XGSP30 Solder Paste: Eutectic Sn63/Pb37 for Board-Level Rework

The Mechanic XGSP30 solder paste gives your repair bench a eutectic Sn63/Pb37 alloy in a 20g pack, built for SMD and BGA rework on mobile phone boards. A eutectic alloy skips the pasty transition range that other tin-lead ratios show, so the paste moves from solid to liquid at one point: 183°C. That single melting point matters on a crowded smartphone motherboard, because you control reflow with your hot air station and you know exactly when the joint flows. Mechanicpk stocks the XGSP30 for Pakistani technicians, repair shops, and service centers that run board-level jobs every day.

Why a 183°C Solder Paste for Mobile Repair Works

The alloy combines 63% tin and 37% lead. That ratio gives a sharp melt, strong wetting, and smooth, uniform joints once the paste reflows. A 183°C solder paste for mobile repair sits well below the heat that lead-free pastes demand, so you put less thermal load on neighboring components, flex connectors, and plastic shields while you work. The paste has a smooth consistency, so you can lay down small, controlled deposits on fine-pitch pads instead of flooding the area. The no-clean, low-residue formulation leaves little flux behind, which shortens your cleanup and helps you inspect the joint under the microscope sooner.

Where XGSP30 Fits in Your Repair Workflow

You reach for this paste whenever a repair needs fresh solder on a pad. Tinning pads before reballing, setting a new SMD capacitor or resistor, and rebuilding a lifted pad after a rough IC change karna job all fit the XGSP30. It also helps when you restore a damaged trace and need a clean pad for jumper lagana. On a dead phone or a charging issue, you often work around the charging IC and power section, where small passives sit tight against each other. A paste that melts at a known temperature keeps those repairs repeatable.

Pair the XGSP30 with the tools that complete the workflow: a hot air station for reflow, a soldering station for pad cleanup, a reballing kit and stencils for BGA work, a PCB holder to keep the board steady, a microscope to inspect joints, and a multimeter to test continuity after you finish. Browse the Hot Air Stations, Soldering Stations, Reballing Kits, PCB Holders, Microscopes, and Multimeters categories on Mechanicpk to build the full bench.

Leaded Paste: What Technicians Should Know

The XGSP30 contains lead, so it suits repair, rework, and prototype work rather than RoHS-regulated manufacturing. Work with good ventilation, keep the paste away from food, and wash your hands after handling it. Seal the pack after each use so the paste stays workable, and follow the storage guidance on the product packaging. If your workshop handles both leaded and lead-free boards, keep a separate tip and clean tinning habits for each so you avoid cross-contamination between alloys.

Additional information
Weight0.20 kg
Q & A
Please login to post questions

Key Features

  • Eutectic Sn63/Pb37 alloy for consistent melting
  • Single melting point of 183°C for predictable reflow
  • Smooth paste consistency for controlled application
  • Strong wetting for uniform solder joints
  • No-clean, low-residue formulation
  • 20g pack sized for daily bench use
  • Suits SMD and BGA rework
  • Fits consumer electronics and precision circuit repair

Specifications

BrandMECHANIC
ModelXGSP30
CategorySolder Paste
CompatibilityUniversal — not device-specific; for SMD and BGA soldering on electronic circuit boards
TechnologyEutectic Sn63/Pb37 alloy (63% tin, 37% lead), 183°C melting point, no-clean low-residue flux
Weight20g

Common Repair Uses

  • Board-level soldering and rework in mobile repair workflows.
  • Tinning pads before BGA reballing
  • SMD component replacement
  • IC change karna pad preparation
  • Rebuilding lifted or damaged pads
  • Jumper lagana for trace restoration
  • Charging issue repair around the power section
  • Dead phone board rework
  • Precision electronic circuit repair

Compatible Devices

  • Universal — not device-specific. Suits any mobile board that uses SMD components or BGA pads.
  • Android smartphone motherboards
  • iPhone logic boards
  • Tablet PCBs
  • Charging and power-section boards
  • Display and touch flex connector pads
  • SMD capacitor and resistor positions
  • BGA IC pads prepared for reballing
  • General consumer electronics circuit boards

FAQ

What is the product name?
The product name is Mechanic XGSP30 Special Solder Paste (20G) 183°C.
What is the brand of this product?
The brand of this product is MECHANIC.
What is the model of this product?
The model of this product is XGSP30.
What is this product used for?
This product is used for SMD and BGA soldering, pad tinning, and board-level rework on mobile phones and other electronic circuit boards.
Which devices are compatible with this product?
This product is universal and not device-specific. It works on any mobile or electronic board that uses SMD components or BGA pads.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is Mechanic XGSP30 solder paste leaded or lead-free?
It is leaded. The alloy is Sn63/Pb37, which means 63% tin and 37% lead.
What is the melting point of Mechanic XGSP30 and is it suitable for BGA reflow?
The melting point is 183°C. The eutectic Sn63/Pb37 alloy suits SMD and BGA reflow work with a hot air station.