2UUL FD23 C210-I Soldering Iron Tip (5 Pack)

₨ 3,000

C210-I Soldering Tip Pack

The 2UUL FD23 C210-I soldering iron tip pack gives you five fine, needle-style tips for precision micro-soldering on mobile phone boards. Each tip follows the C210 cartridge standard, so the heating element sits inside the tip and heat reaches the pad quickly. Use it for pad cleanup, jumper wire lagana, FPC connector pads, and tin bridge correction around small ICs and passives. Fit it to a C210-compatible handle or station and keep a spare tip ready whenever oxidation or heavy rework wears one down. Pair it with your microscope and PCB holder for clean, controlled joints on every hardware fault repair.

In stock

13 People watching this product now!
Description

C210-I Soldering Iron Tip for Precision Board Repair

The C210-I soldering iron tip gives your micro-soldering station a fine, needle-style point for jobs where a broad tip covers too much board. This 2UUL FD23 pack puts five I-type tips on your bench in a single order, so you always have a fresh tip ready when oxidation or heavy rework wears the working surface down. The FD23 follows the C210 cartridge standard, which places the heating element inside the tip itself. That layout moves heat to the pad fast and recovers quickly between joints. If your bench runs a C210-compatible handle or station, you swap the tip in and keep working.

Cartridge Design and Heat Transfer

A C210 tip works differently from a 900M-style tip. A 900M tip slides over a heater built into the handle, while a C210 cartridge carries the heater inside the tip. The two standards do not interchange, so match this pack to a C210 handle or station before you order. The FD23 body uses iron-plated copper, a combination that carries heat from the heater to the point and resists erosion from repeated tinning. Seat each tip fully in the handle, because a loose fit weakens heat transfer and makes the temperature swing. Clean and re-tin the tip after each session to slow oxidation and keep solder flowing smoothly.

Where the I-Type Point Earns Its Place

The fine point lets you touch a single pad without disturbing its neighbours. You reach charging port pads, FPC connector pads, and tight rows of small passives on dead phone boards where a larger tip would melt nearby components. When you run a jumper lagana job to repair a broken trace, the needle point places the wire end exactly where it belongs. It also clears tin bridges between closely spaced pins during IC change karna cleanup, and it tins pads before you reseat a replacement chip. For broad surfaces such as CPU tin dragging or large ground planes, switch to a wider tip from the same C210 family, and keep this I-type tip for the detail work. Under a microscope, the fine point gives you the control that board-level charging issue and display problem repairs demand.

Buying a 5-Pack for a Busy Workshop

Tips wear out faster in a shop that handles daily board work, and a five-tip pack keeps your station productive without waiting on a reorder. You rotate a fresh tip in when the plating wears through, and you keep the station running through a full day of repairs. Build your bench around it with a C210-compatible soldering station, a microscope, a PCB holder, and a multimeter for continuity checks before and after each joint. Add a hot air station for component removal and a reballing kit when you move from pad work to BGA rework, and use a test box to confirm the phone boots after the repair. This I-type pack covers the fine-detail step in that chain, and you can step up to broader or ball-point tips from the same C210 range as your jobs grow.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • Fine, needle-style I-type tip for precision work
  • C210 cartridge standard with the heating element built into the tip
  • Iron-plated copper construction for steady heat transfer
  • Five-tip pack for continuous bench use
  • Fast heat-up and recovery between joints
  • Works with C210-compatible handles and stations
  • Suits SMD, FPC pad, and small IC soldering under a microscope
  • Plug-in replacement for worn C210 tips

Specifications

Brand2UUL
ModelFD23 (C210-I Series), 5-tip pack
CategorySoldering Iron Tips
CompatibilityC210 cartridge-standard soldering handles and stations (T210 handle)
TechnologyC210 cartridge tip with integrated heating element
MaterialIron-plated copper

Common Repair Uses

  • Fine-point soldering and rework on mobile phone boards and small electronics.
  • Micro-soldering on small SMD pads
  • Jumper wire lagana on broken traces
  • Pad cleanup before IC change karna
  • Tin bridge correction between close pins
  • FPC connector pad repair
  • Charging port and charging IC area repair
  • Tinning pads before component reseating
  • General board-level hardware fault repair

Compatible Devices

  • Universal micro-soldering tip for C210-standard handles and stations. It is not tied to specific phone models and works on the boards of any phone you repair at board level.
  • T210 soldering handle
  • C210-standard soldering stations
  • 2UUL FIND210 soldering station
  • 2UUL NT210 NextTip soldering station
  • Samsung and Oppo logic boards (board-level soldering work)
  • Vivo, Infinix, and Tecno logic boards (board-level soldering work)
  • iPhone series logic boards (board-level soldering work)
  • General PCB and SMD rework benches

FAQ

What is the product name?
The product name is 2UUL FD23 C210-I Soldering Iron Tip (5 Pack).
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FD23 (C210-I series).
What is this product used for?
This product is used for fine-point micro-soldering, pad cleanup, jumper wire work, and tin bridge correction on mobile phone boards.
Which devices are compatible with this product?
This product is compatible with C210 cartridge-standard soldering handles and stations, including the T210 handle. It is a universal soldering tip, so it is not limited to specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Will the C210-I tip fit a 900M-style soldering iron?
No. A C210 tip is a cartridge with the heating element built in, while a 900M tip slides over a heater in the handle. The two standards do not interchange, so you need a C210-compatible handle or station.
Which soldering jobs suit the I-type tip on a dead phone board?
The fine I-type point suits pad cleanup, jumper wire placement, FPC connector pads, and tin bridge correction around small ICs. For broad areas such as CPU tin dragging, use a wider C210 tip instead.