JCID V1S Pro X-14PM Face ID R&W Module (No External Power)
₨ 19,000
X-14PM Face ID Module Overview
The JCID X-14PM Face ID activation and R&W module plugs into your V1S Pro or V1SE host and activates the iPhone dot projector without any external power supply. One adapter handles activation, testing, reading and writing of Face ID data for iPhone X through iPhone 14 Pro Max and iPad A12X models. The module recognizes a reversed FPC automatically, so you skip the soldering and alignment steps that slow down Face ID jobs. Pakistani repair shops use it to fix Face ID hardware faults through FPC replacement, chip replacement, or direct testing on the original module.
In stock
X-14PM Face ID Activation Module: Power-Free Dot Matrix Repair for iPhone X–14 Pro Max
The X-14PM Face ID activation module from JCID removes the external power supply from dot projector work. You connect it to a V1S Pro or V1SE host, and the adapter handles the activation path on its own. JCID calls it the first Face ID activation adapter that needs no outside power, and the manufacturer states it improves the activation success rate and protects the projector chip better than the older powered setup. On a Face ID job, that gives you fewer cables on the bench and one less variable when a module refuses to activate.
Host Compatibility and Operating Scope
This module matches the JCID V1S Pro and the V1SE. The original V1S does not support it, so check your host before you order. JCID added the X-14PM function to V1S Pro software in version V1.60, so update your software before you connect the adapter. With the WiFi connection on the V1SE or V1S Pro, you run one-key activation, reading and writing from a single adapter instead of swapping between separate test boards. The module covers dot matrix work on iPhone X through iPhone 14 Pro Max and on iPad A12X models.
Repair Workflow Fit
Face ID not working is a hardware fault that usually sends you down one of three paths, and this module supports all three. You can test and repair Face ID without dismantling the dot matrix, replace the FPC, or replace the chip. The adapter recognizes a reversed FPC automatically, which removes a common cause of failed activation when you connect a flex backwards. The adapter itself needs no soldering and no alignment, so even a junior technician on your bench can run a clean activation test.
When a job needs board-level work, you pair this module with the rest of your iPhone repair setup. Hot air stations and soldering stations handle chip replacement, a microscope lets you inspect pads and flex connectors, and a multimeter confirms lines before you power up. PCB holders keep the board steady, and reballing kits cover the cases where a chip change goes beyond a simple swap. After every repair, you activate and test the module before you close the phone, which catches a bad joint or a damaged flex early.
Why Technicians Choose It
Power-free activation changes how you plan a Face ID repair. You no longer wire in a separate supply, so setup time drops and the risk of feeding the wrong voltage to the dot projector drops with it. The adapter combines activation, testing, reading and writing in one small green unit, which keeps your drawer clean compared with carrying a different board for each function.
If you run a service center that handles volume iPhone repairs, one adapter per host station keeps your Face ID jobs moving. It sits alongside your other tools in the same workflow: ISP pinout tools and eMMC programmers for storage faults, UFS adapters for newer Android boards, and test boxes for general diagnostics. Mechanicpk stocks the full range, so you build the bench in one order. If a customer’s phone arrives with a dead Face ID after a screen or flex replacement, this module gives you a direct way to test, read and write the dot matrix data on the spot.
| Weight | 0.31 kg |
|---|
Key Features
- ✓Activates the dot projector without an external power supply
- ✓Combines activation, testing, reading and writing in one adapter
- ✓Works with JCID V1S Pro and V1SE hosts
- ✓Supports one-key activation, read and write over WiFi
- ✓Recognizes a reversed FPC automatically
- ✓Needs no soldering and no alignment on the adapter
- ✓Supports Face ID repair without dismantling the dot matrix
- ✓Supports repair by FPC replacement or chip replacement
Specifications
| Brand | JCID |
|---|---|
| Model | X-14PM Face ID Activation/R&W Adaptor (No External Power) |
| Category | iPhone Face ID Repair Adapter |
| Compatibility | JCID V1S Pro, JCID V1SE (not compatible with V1S) |
| Supported Devices | iPhone X to iPhone 14 Pro Max, iPad A12X |
| Technology | Dot matrix activation, testing, read and write without external power supply |
Common Repair Uses
- ✓Face ID activation, testing, and data read/write on dot projector modules
- ✓Activating the dot projector without an external power supply
- ✓Testing the dot matrix module after a repair
- ✓Reading Face ID data from the original module
- ✓Writing Face ID data to a replacement module
- ✓Repairing Face ID without dismantling the dot matrix
- ✓Repairing Face ID by replacing the FPC
- ✓Repairing Face ID by replacing the chip
- ✓Running one-key activation, reading and writing over WiFi
Compatible Devices
- ✓iPhone X to iPhone 14 Pro Max and iPad A12X, used with JCID V1S Pro or V1SE hosts
- ✓iPhone X
- ✓iPhone XS and XS Max
- ✓iPhone XR
- ✓iPhone 11 series
- ✓iPhone 12 series
- ✓iPhone 13 series
- ✓iPhone 14 series up to 14 Pro Max
- ✓iPad A12X models (iPad Pro 3 and 4)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the X-14PM Face ID module work with the JCID V1S?
Does the X-14PM need an external power supply to activate Face ID?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



