Mijing HY-228 Lead-Free Halogen-Free Solder Paste 10cc
₨ 700
Mijing HY-228 Flux-Type Solder Paste 10cc
Mijing HY-228 is a lead-free, halogen-free, high-activity solder paste in a 10cc pack for mobile phone board work. Mechanicpk supplies it to technicians who solder BGA chips, ICs and motherboard components and need clean wetting without false joints. The antioxidant formulation resists oxidation, leaves low residue, cleans easily and produces only slight smoke at the bench. You get a compact pack that fits a daily repair kit and suits shops that run frequent IC change and reballing jobs on smartphone boards.
In stock
Mijing HY-228 Solder Paste for Clean BGA and IC Soldering
Mijing HY-228 solder paste gives your repair bench a lead-free, halogen-free, high-activity paste for BGA, IC and motherboard soldering. Mijing lists it as a multifunctional paste, and suppliers sell it as a 10cc soldering consumable. You use it where wetting quality decides whether a joint holds, whether you reseat a chip on a dead phone board or rework a small component after a hardware fault. This listing explains what the paste does, where it fits in a chip-level workflow and how to pair it with the rest of your bench.
Lead-Free and Halogen-Free High-Activity Formula
The formula contains no lead and no added halogens. Lead-free chemistry keeps your bench in line with current soldering practice. A halogen-free flux system lowers the risk of corrosive residue around fine pads and IC contacts. High activity means the paste lifts oxide from pad surfaces quickly, so solder wets the joint instead of balling up. The antioxidant formulation targets false welding, the cold-joint fault behind many intermittent hardware problems. Boards you rework with this paste leave your bench with joints that wet fully and hold under handling.
Where HY-228 Fits in Your Repair Workflow
A typical chip-level job starts with lifting the faulty IC using a hot air station. Next you clean the pads under a microscope, apply a thin layer of paste and reseat or reball the component. HY-228 belongs in that apply-and-reflow step. You spread it across BGA pads or around IC contacts, then bring the area up to temperature with your hot air station or soldering station. Low residue and easy cleaning mean you inspect the finished joint without scrubbing through a heavy film. Slight smoke keeps fumes manageable, though you still run ventilation at your repair bench. Technicians who do IC change karna and motherboard rework every day get a dependable paste in a pack that stays easy to reach.
Building a Complete Soldering Setup Around It
Paste works best inside a controlled setup. Pair HY-228 with a reballing kit for BGA work, PCB holders to keep the board steady during reflow, a microscope for pad inspection and a hot air station or soldering station for heat control. Shops that start with basic flux jobs often grow into full reballing and IC replacement, and adding these tools step by step builds that capability without replacing what you already own. Supplier information credits the paste with a lower failure rate and longer service life in repaired electronics, which matters when customers expect a repair to last. For Pakistani workshops that handle charging issue, display problem and network issue boards daily, a 10cc tube gives you fresh paste for each job.
| Weight | 0.50 kg |
|---|
Key Features
- ✓Lead-free formulation
- ✓Halogen-free formulation
- ✓High-activity paste
- ✓Antioxidant flux paste for BGA, IC chips and motherboard soldering
- ✓Targets false welding for stronger joints
- ✓Low residue after soldering
- ✓Easy to clean
- ✓Slight smoke during use
Specifications
| Brand | Mijing |
|---|---|
| Model | HY-228 |
| Category | Solder Paste / Soldering Consumables |
| Compatibility | Universal — not device-specific; suited to BGA, IC and motherboard soldering |
| Technology | Lead-free, halogen-free, high-activity, antioxidant paste; 10cc pack |
Common Repair Uses
- ✓Verified scope covers chip-level and board-level soldering
- ✓BGA chip soldering and rework
- ✓IC replacement (IC change karna)
- ✓Motherboard soldering for hardware fault boards
- ✓Reducing false welding in reworked joints
- ✓Electronic component repair
- ✓Battery soldering repair
Compatible Devices
- ✓Universal — not device-specific; verified scope covers general mobile phone board soldering
- ✓Smartphone motherboards (brand-independent)
- ✓BGA chips on mobile logic boards
- ✓IC chips on motherboards
- ✓SMD components on mobile PCBs
- ✓General electronic component repair boards
- ✓Battery soldering repair work
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is Mijing HY-228 lead-free and halogen-free?
Does Mijing HY-228 leave residue after soldering?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



