JTX F1 Conductive Silver Paste for Mobile Repair
₨ 1
Conductive Silver Paste for Mobile Repair
The JTX F1 Conductive Silver Paste from JITONGXUE gives your bench a dependable way to rebuild broken circuit lines without running jumper wire. This conductive silver paste for mobile repair offers ultra-low resistance, high conductivity, and strong adhesion on PCB, glass, ceramic, and plastic surfaces. You brush it onto the damaged line, dry it with heat, and the paste forms a conductive path across the break. Technicians use it for iPhone and Android screen line faults, flexible screen circuits, and fine motherboard traces. Mechanicpk supplies the JTX F1 to Pakistani repair shops and service centers that need a repeatable fix for display problem jobs.
Out of stock
Conductive Silver Paste for Mobile Repair: JTX F1 Technical Overview
A cracked trace or a lifted screen line turns a repairable handset into a dead phone on the counter. The JTX F1 Conductive Silver Paste, made by JITONGXUE, is a conductive silver paste for mobile repair that bridges those breaks without a jumper wire or a soldering iron. Its ultra-low resistance keeps current loss minimal across the repaired line. It bonds to PCB, glass, ceramic, and plastic surfaces, which covers the substrates you meet on phone motherboards, display flex cables, and screen circuits. Below you will find how the paste works, where it fits in your repair workflow, and how to apply it for a clean result.
How JTX F1 Silver Paste Rebuilds a Broken Line
Silver paste works as a conductive adhesive. Silver particles sit inside a binder, and heat drying pulls them into a continuous path across the gap. The JTX F1 relies on that principle, pairing low resistance with strong adhesion, so the rebuilt line carries signal without the bulk of a solder joint. Because the paste avoids the high temperatures of soldering, it suits heat-sensitive flex circuits and screens. The application stays short. Dip a soft-tipped brush or a fine blade into the paste, lay it across the broken line, then heat and dry it until it forms the conductive path. Clean the damaged area first so the paste meets bare copper or the exposed screen line. Stir the paste before you load the brush, and work under magnification so the line stays narrow and continuous. After the paste cures, cover the repair with green oil. The insulation layer stops the new line from shorting against its neighbors.
Where It Fits in Your Repair Workflow
Most JTX F1 jobs start with a display problem. Water damage often leaves green lines, white screens, or dead touch zones on iPhone and Android panels, and the fault traces back to a broken flex circuit line. You locate the break under a microscope, confirm it with a multimeter continuity check, and secure the board in a PCB holder. The paste then replaces the missing section of the line. Technicians also use it on fine motherboard traces where a jumper wire would sit too thick or lift neighboring pads. You dry the paste with a hot air station set to a gentle temperature, since heat-sensitive screens and flex cables punish aggressive airflow. When a job needs a solid wired connection instead, you move up to a soldering station with jumper wire. Reballing kits and soldering stations cover the pad-level hardware fault jobs, and the silver paste covers the line-level breaks between them.
A repair bench follows a fixed order on these jobs: diagnose, clean, apply, cure, insulate, test. Power the screen after the green oil sets and check the display and touch response before you close the phone. A line that still shows a fault points you back to the microscope, where you check for a second break or a gap the paste missed. That loop keeps comebacks low and your warranty claims short.
Buying Notes for Pakistani Repair Shops
One consumable covers screen lines, flex circuits, and board traces, which keeps your shelf simple when display problem jobs arrive daily. Ultra-low resistance protects signal quality on the repaired line, and adhesion across PCB, glass, ceramic, and plastic means you never swap products between substrates. Mechanicpk supplies the JTX F1 to repair shops, service centers, and training institutes across Pakistan, and it pairs with the microscopes, multimeters, hot air stations, and PCB holders in the catalog. Shops that run screen and board repairs every day get the most from it, since the same paste serves iPhone and Android jobs alike. Store the paste sealed between jobs and apply it sparingly. A thin, controlled line keeps the repair neat and lowers the risk of bridging to adjacent traces.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Ultra-low resistance for minimal current loss across the repaired line
- ✓High electrical conductivity that restores circuit continuity
- ✓Strong adhesion to PCB, glass, ceramic, and plastic
- ✓Rebuilds broken lines without jumper wire or soldering
- ✓Brush or blade application for narrow, controlled lines
- ✓Heat-dry process forms the conductive path
- ✓Suits iPhone and Android screen line repair
- ✓Pairs with green oil insulation to prevent short circuits
Specifications
| Brand | JITONGXUE (JTX) |
|---|---|
| Model | F1 |
| Category | Conductive Silver Paste (Mobile Repair Consumables) |
| Compatibility | PCB, glass, ceramic, and plastic surfaces |
| Supported Devices | iPhone and Android phone screens and motherboards |
| Technology | Ultra-low resistance conductive silver paste |
| Material | Silver-based conductive paste |
Common Repair Uses
- ✓Line and trace repair where a break interrupts a circuit.
- ✓Restoring green line and white screen faults after water damage
- ✓Repairing broken lines on flexible screen circuits
- ✓Rebuilding damaged motherboard traces
- ✓Bridging small circuit gaps without jumper wire
- ✓Repairing flex cable line breaks
- ✓Fixing dead touch zones caused by broken screen lines
- ✓Reconnecting circuits on glass and ceramic substrates
- ✓Line repair on heat-sensitive parts where soldering risks damage
Compatible Devices
- ✓Verified scope covers phone screen circuits and boards, plus the surface materials below. It does not list specific phone models.
- ✓iPhone screen line and flex circuit repair
- ✓Android phone screen line and flex circuit repair
- ✓Mobile phone motherboards (broken trace repair)
- ✓Flexible screen and flex cable circuits
- ✓PCB surfaces
- ✓Glass surfaces
- ✓Ceramic surfaces
- ✓Plastic surfaces
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does JTX F1 silver paste need heat to work after application?
Should I insulate the line after repairing it with JTX F1 silver paste?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



