Relife RL-601Q Pro Rotating Damping Tempered Glass Fixture
₨ 4,500
Rotating Glass PCB Fixture for Precision Rework
The Relife RL-601Q Pro Rotating Damping Tempered Glass Fixture holds mobile phone motherboards, CPUs and precision ICs steady during microscope-level repair. This rotating glass PCB fixture turns through a damped 360° and locks the board with a beveled inner-lock, so nothing slips while you work. The tempered glass surface withstands 500°C+ without deformation, and the design accepts single-layer and double-layer motherboards. You get a compact, portable holder for hot air rework, IC change and reballing jobs at your bench or service center. Buy it from Mechanicpk for professional mobile repair in Pakistan.
In stock
Rotating Glass PCB Fixture Built for Microscope-Level Board Work
The Relife RL-601Q Pro Rotating Damping Tempered Glass Fixture gives your bench a stable, heat-resistant platform for mobile phone motherboards, CPUs, chips and other precision ICs. As a rotating glass PCB fixture, it combines a damped 360° base with a beveled inner-lock that grips the board edge, so the board stays seated while you apply hot air, solder or probe under a microscope. Relife designed it for technicians who handle IC-level repair daily and cannot afford a board that creeps mid-rework. If you repair dead phones, chase hardware faults or run a service center queue, this fixture removes one variable from every job.
Damped 360° Rotation for Microscope Work
Board repair happens in a tiny field of view. When you bump a loose board, you lose your target pad and spend seconds finding it again. The damped base on the RL-601Q Pro rotates through a full 360° with controlled resistance, so you turn the board smoothly instead of lifting it, repositioning it and refocusing. You reach every side of a CPU, PMIC or flash IC without moving the microscope, and your work stays centered under the lens. Technicians who inspect, heat and re-inspect the same corner dozens of times per shift gain the most, because every saved adjustment adds up across a full bench day. The damping also keeps the motion deliberate, which matters when you hold a hot air nozzle in one hand and tweezers in the other.
Tempered Glass Surface and Beveled Inner-Lock
The work surface uses tempered, heat-resistant glass rated for 500°C+. It resists deformation and corrosion, so repeated hot air cycles do not warp it, and flux residue wipes off without etching the surface. The beveled inner-lock design clamps the motherboard from its edges and holds it without slipping. It accepts both single-layer and double-layer motherboards, which covers the stacked boards in many current phones and the single-layer boards you still see on older models. The same locking design supports chips, CPUs and ICs removed from the board, so you do not need a second holder for loose parts. The unit stays compact and lightweight, which suits a crowded bench or a technician who carries a kit between shops.
Where It Fits in Your Repair Workflow
You place the RL-601Q Pro between diagnosis and final testing. Whether the job is a dead phone, a boot loop, a hang on logo that points to a failing eMMC, or a charging issue traced to a charging IC, you check the board with a multimeter first. Once you confirm the hardware fault, you clamp the board here and start the rework: remove the shield, preheat with your hot air station, lift the faulty IC and clean the pads. Pair the fixture with a good microscope and a temperature-controlled soldering station so every step happens on one steady surface.
When you reball a CPU or change an eMMC or UFS chip, the fixture holds the board while you work. The same setup helps when you solder ISP wires to test points for eMMC programmer access. Technicians who want to build out the bench can add reballing kits, extra PCB holders and test boxes to the same workflow. If your shop currently balances boards on a foam pad or a flat plate, this fixture is the practical first upgrade toward a proper microscope station.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Damped 360° rotation for smooth, controlled board movement
- ✓Tempered heat-resistant glass rated for 500°C+
- ✓Beveled inner-lock design that grips the board without slipping
- ✓Supports single-layer and double-layer motherboards
- ✓Holds chips, CPUs and ICs as well as full boards
- ✓Deformation-free and corrosion-resistant glass surface
- ✓Glass surface that cleans easily after flux and solder work
- ✓Compact, lightweight and portable body
Specifications
| Brand | Relife |
|---|---|
| Model | RL-601Q Pro |
| Category | PCB Repair Fixture / Motherboard Holder |
| Compatibility | Single-layer and double-layer motherboards, chips, CPUs and ICs |
| Supported Devices | Mobile phone motherboards, CPUs, chips and precision ICs |
| Technology | Damped 360° rotation, beveled inner-lock clamping, 500°C+ heat-resistant tempered glass |
| Material | Tempered glass |
Common Repair Uses
- ✓Real bench workflows where a rotating, heat-safe board holder is used
- ✓Hot air IC removal and replacement
- ✓CPU and chip rework
- ✓Reballing preparation and reflow work
- ✓eMMC and UFS chip change
- ✓Charging IC and PMIC replacement
- ✓Soldering ISP wires to test points
- ✓Board cleaning and flux removal under a microscope
- ✓Hardware fault inspection on dead phone motherboards
Compatible Devices
- ✓Universal board-level scope, holds the board rather than matching a specific phone model
- ✓Single-layer mobile phone motherboards
- ✓Double-layer mobile phone motherboards
- ✓Mobile phone CPU chips
- ✓Standalone chips under rework
- ✓Precision ICs on bare boards
- ✓Hard drive boards and similar small precision boards
- ✓Boards from any phone brand, since the lock grips the board edge
- ✓Microscope-based board work on compact PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the RL-601Q Pro hold double-layer motherboards?
What temperature can the glass surface of the RL-601Q Pro handle during hot air work?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



