YCS 199°35g Soldering Paste Needle-Type
₨ 800
199°C Solder Paste for Mobile Repair in a 35g Syringe
YCS 199°35g Soldering Paste Needle-Type gives your repair bench a 199°C solder paste for mobile repair in a 35g needle-type syringe. You dispense paste pad by pad on BGA, SMD and phone PCB work instead of scooping it from a jar. The supplier adds silver particles to improve conductivity and cut cold solder joints, so fewer boards come back for rework. Mechanicpk supplies it to repair shops and service centers across Pakistan that need controlled, repeatable paste placement on motherboard, chip and BGA jobs.
In stock
199°C Solder Paste for Mobile Repair: Syringe-Dispensed Control
YCS 199°35g Soldering Paste Needle-Type is a 199°C solder paste for mobile repair that ships in a 35g needle-type syringe. The syringe puts paste exactly where a BGA pad or SMD joint needs it, and that precision defines how this product fits a professional bench. Mechanicpk stocks it for technicians who rebuild phone motherboards daily and want measured dispensing, a clean work area, and joints they trust. You pair it with a hot air station or soldering station and finish the job on the board, not in the mess around it.
Needle-Type Dispensing and the 199°C Rating
The needle-type syringe holds 35g of paste and releases it through a fine tip when you press the plunger. You lay a small bead on a single pad, dot a row of pads on a connector, or tin a fresh BGA footprint without smearing the neighbouring components. The 199°C rating tells you which temperature class the paste belongs to, so you can match your hot air profile to the chip and board in front of you. Run a test on a scrap board whenever you switch to a new paste, because every motherboard soaks up heat differently. Cap the syringe after each job so the needle stays clear for the next repair. Pad-by-pad control also saves paste. A 35g syringe stretches across many repairs when you dispense only what each pad needs, which keeps your consumable cost per board predictable. Busy shops running dozens of boards a week benefit most from that predictability.
Silver Particles and Joint Quality
The supplier describes this paste as high density with strong welding strength and high resistance, and it adds silver particles to lift conductivity. For a repair technician, that combination targets the faults that cost the most time: cold solder joints that pass a quick look and then fail under load. A dead phone that comes back after a rushed reflow, a charging issue that returns after a port repair, or a hang on logo caused by a weak joint under a chip all point to joint quality. Consistent paste placement helps you avoid that second visit. Silver content also matters when you rework fine pads that carry signal and power lines. Full, clean joints give you stable contact, and stable contact keeps a repaired board running after it leaves your bench. Inspect every finished joint under a microscope before you close the phone, and rework any joint that looks dull or uneven.
Where It Fits in Your Repair Workflow
Start with diagnosis. Use a multimeter to trace a hardware fault, and use a test box or your usual tools to confirm the symptom. Lift the suspect chip with your hot air station, clean the pads with your soldering station, and hold the board steady in a PCB holder. Apply this paste to the pads, set the chip or the reballing stencil in place, and reflow with controlled heat. The same paste supports BGA reballing, SMD component replacement, and general motherboard rework, so one syringe covers several repair types on your bench.
Technicians who also work with storage chips will link this step to ISP and eMMC jobs. When a boot loop or a dead-after-flash phone sends you toward an eMMC or UFS repair, browse our ISP Pinout Tools, eMMC Programmers and UFS Adapters, then come back to this paste for the soldering stage. If you are building a rework setup from scratch, pick up a Hot Air Station, a Soldering Station and a Reballing Kit together with the syringe. The compact 35g syringe suits shops that move through paste steadily and want a fresh, easy-to-handle format for every repair session. Between jobs, wipe the needle tip and store the syringe upright with the cap on, away from heat.
| Weight | 0.35 kg |
|---|
Key Features
- ✓35g needle-type syringe for pad-by-pad dispensing
- ✓199°C rated solder paste
- ✓Silver particles added to improve conductivity
- ✓Made for mobile phone motherboard, PCB, BGA and SMD chip soldering
- ✓High-density paste with strong welding strength
- ✓Built to reduce cold solder joints and rework
- ✓Single-syringe pack that stays easy to store and handle
- ✓Fits BGA reballing, SMD rework and general motherboard repair
Specifications
| Brand | YCS |
|---|---|
| Category | Solder Paste |
| Compatibility | Universal, not device-specific. Suited to mobile phone motherboards, PCBs, BGA and SMD chips |
| Technology | Silver-particle solder paste in a needle-type syringe |
| Temperature Rating | 199°C |
| Weight | 35g |
| Package Contents | 1 x 35g syringe of solder paste |
Common Repair Uses
- ✓Soldering and rework on mobile phone boards where you place paste in small, controlled amounts.
- ✓BGA chip soldering and reballing preparation
- ✓SMD chip and component replacement
- ✓Motherboard rework after a hardware fault
- ✓Re-soldering weak joints behind charging issues
- ✓Re-soldering weak joints behind hang on logo faults
- ✓PCB repair and pad tinning
- ✓Reflow work after IC removal
- ✓Reducing cold solder joints and repeat rework
Compatible Devices
- ✓Universal use on mobile phone motherboards and PCBs. The listing does not tie the paste to specific phone models or brands.
- ✓Mobile phone motherboards (universal, not device-specific)
- ✓Phone and general electronics PCBs
- ✓BGA chip footprints
- ✓SMD chips and components
- ✓Boards worked with a hot air station
- ✓Boards worked with a soldering station
FAQ
What is the product name?
What is the brand of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How much paste does the syringe hold?
What temperature is the YCS 199°C syringe solder paste rated for?
Can I use this paste for BGA and SMD chip repair on phone motherboards?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



