Relife RL-049 CPU Removal Tools – 5-in-1 CPU Cutter
₨ 1
Relife RL-049 CPU Removal Tool
The Relife RL-049 CPU Removal Tools give your repair bench a 5-in-1 CPU cutter built for separating chips from iPhone, iPad, laptop and LCD boards. The ultra-thin blade slides under a heated chip, resists high temperature without deforming, and wears slowly through repeated jobs. Its non-stick tin surface lifts solder spots off the pads instead of dragging them across the board. If you handle CPU removal, underfill clean-up or tin-spot separation every week, this Relife RL-049 CPU removal tool replaces improvised blades with a purpose-built edge that suits professional mobile repair workshops across Pakistan.
Out of stock
Relife RL-049 CPU Removal Tools for Precision Chip Separation
The Relife RL-049 CPU removal tool targets one job on the repair bench: separating a CPU or similar BGA chip from a board without tearing pads or gouging the PCB. Relife builds the RL-049 as a 5-in-1 cutter with an ultra-thin blade, aimed at technicians who work on iPhone, iPad, laptop and LCD boards. A tool this thin matters in mobile repair Pakistan workshops, where a dead phone often arrives with a CPU that needs lifting before any reballing can start.
Blade Construction and Thermal Behaviour
The blade of the Relife RL-049 stays ultra-thin yet tough, so it slips into the gap under a heated chip and keeps its shape under pressure. Relife lists high temperature resistance, no deformation and wear resistance for this edge, which means you can work next to a hot air stream without the blade softening or bending. The non-stick tin surface separates solder spots quickly, so molten solder does not cling to the cutter and drag across neighbouring pads. That behaviour protects board traces on dense iPhone logic boards where one scraped pad turns a clean CPU job into a hardware fault repair.
Where It Sits in the CPU Rework Workflow
You use the RL-049 in the middle of the CPU rework sequence. Secure the board in a PCB holder, bring the chip to temperature with a hot air station, then slide the blade under the chip edge to break the underfill and solder bond. After the chip lifts, the same tool helps clear leftover underfill and tin from the pads before you reball the CPU or fit a replacement. Technical listings also point to underfill cleaning and SMD component separation as supported uses, so one blade covers lifting, cleaning and neighbouring component work on a single board. Under a microscope, the thin edge gives you the visual control you need to keep each cut shallow and aimed.
Who Benefits Most on the Bench
Repair shop owners who run daily board-level jobs get the most from a tool like this, because the RL-049 cuts down pad damage and rework time on every CPU job. Technicians starting IC-level work gain a low-cost entry tool that pairs naturally with soldering stations, reballing kits and a stable PCB holder. Service centres that standardise their rework kit can stock the Relife RL-049 alongside multimeters and test boxes, so each technician starts the same CPU job with the same edge. Training institutes also benefit, since students learn clean chip separation on a blade designed for the purpose rather than on a scalpel or a repurposed screwdriver.
Where the RL-049 Supports Your Repair Bench
CPU removal rarely stands alone. A technician diagnosing a boot loop issue, a hang on logo fault or a no-charging board often traces the problem to a chip that needs lifting, inspecting and reseating. The Relife RL-049 fits those jobs because it handles heated separation, tin-spot clean-up and underfill scraping with one edge. Keep it next to your hot air station and microscope, and you cut the tool changes that slow a CPU job down.
| Weight | 0.15 kg |
|---|
Key Features
- ✓5-in-1 CPU cutter design
- ✓Ultra-thin blade for tight chip gaps
- ✓Good blade toughness under pressure
- ✓High temperature resistance
- ✓No deformation during use
- ✓Wear-resistant edge
- ✓Non-stick tin surface for fast solder-spot separation
- ✓Suits iPhone, iPad, laptop and LCD CPU removal
Specifications
| Brand | Relife |
|---|---|
| Model | RL-049 |
| Category | Mobile Repair Tools – CPU and Chip Removal Blades |
| Compatibility | iPhone, iPad, laptop and LCD CPU removal |
| Supported Devices | iPhone, iPad, laptop and LCD boards |
Common Repair Uses
- ✓Verified scenarios for heated CPU and chip separation, underfill cleaning and tin-spot removal.
- ✓CPU removal from iPhone logic boards
- ✓CPU removal from iPad logic boards
- ✓Laptop CPU and chip separation
- ✓LCD board chip removal
- ✓Underfill glue cleaning around BGA chips
- ✓Tin-spot separation on pads
- ✓SMD component separation
- ✓Pad clean-up before reballing
Compatible Devices
- ✓Verified scope covers CPU and chip removal on iPhone, iPad, laptop and LCD boards. The tool is not tied to specific models.
- ✓iPhone logic boards (CPU removal)
- ✓iPad logic boards (CPU removal)
- ✓Laptop motherboards (CPU removal)
- ✓LCD panel boards (CPU removal)
- ✓BGA chips with underfill
- ✓SMD components needing separation
- ✓Flash memory and storage chips on boards
- ✓Universal blade – not device-specific
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Do the RL-049 blades keep their shape near a hot air station?
Can the Relife RL-049 clean underfill glue around a BGA CPU?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



