2UUL BA14PS Back Cover Sealing Adhesive for iP14 Plus
₨ 900
iPhone 14 Plus Back Cover Seal Pack
The 2UUL BA14PS Back Cover Sealing Adhesive for iP14 Plus(5pcs/Pack) gives your bench five pre-cut, double-sided seals made for the iPhone 14 Plus rear glass and frame. Each piece replaces the factory adhesive you destroy when you open the back for a battery change, charging issue repair, speaker job, or back glass replacement. You clean the frame, lay the tape, and bond it with a heated press to restore the airtight seal. The BA14PS code targets the iPhone 14 Plus only, so you match the part to the phone before you start. Mechanicpk supplies this iPhone 14 Plus back cover sealing adhesive to technicians and repair shops across Pakistan.
In stock
iPhone 14 Plus Back Cover Sealing Adhesive for Clean Rear Glass Resealing
The 2UUL BA14PS Back Cover Sealing Adhesive for iP14 Plus(5pcs/Pack) is a model-specific iPhone 14 Plus back cover sealing adhesive that gives technicians a pre-cut, double-sided seal for the rear glass and frame. Every job that opens the back of an iPhone 14 Plus destroys the factory adhesive ring. You remove it to reach the battery, the charging port assembly, or the logic board, and you need a fresh seal before you close the phone. This pack supplies five pre-cut pieces, so you finish five reseals without trimming tape by hand or guessing at the outline.
Pre-Cut Back Glass Adhesive for iPhone 14 Plus: Fit and Pack Details
2UUL cuts each piece for the iPhone 14 Plus rear frame, so the outline follows the bonding surface instead of a generic strip. The supplier lists the piece at 145 x 70 x 0.5 mm, a thin profile for a double-sided gasket. The pack holds five pieces, which suits a bench that handles several iPhone 14 Plus rear glass jobs every week. The BA14PS code marks the iPhone 14 Plus version inside the 2UUL BA series, which also covers other iPhone 14 to iPhone 17 models. Each BA code targets one model, so order the code that matches the phone on your bench. A wrong-model piece costs you the same time as no piece at all.
Where the Adhesive Fits in Your Repair Workflow
The seal goes on last in a back glass workflow. You separate the glass, finish the repair, clean the frame, and check it for deformation. Then you lay the 2UUL tape onto the frame and bond it under heat and pressure. 2UUL points to a heating press such as its DA07 Mini Hot Press Station for that final bond, which restores the airtight seal on the frame. Before you seal, power the phone on and test the repair. Use a multimeter to confirm the battery connector and charging line when the job started as a charging issue or hardware fault. Hold the board in PCB holders during board work, and check solder joints under a microscope. A hot air station from the Hot Air Stations range handles the heat side of component work, and this adhesive closes the job afterward.
Why Shops Stock It Beside Their Back Glass Parts
A repair shop in Pakistan that replaces iPhone 14 Plus back glass, swaps batteries, or clears display problem and charging faults opens the rear panel again and again. Keeping a dedicated model pack on the shelf removes the delay of cutting generic tape and keeps your turnaround steady. You can pair it with its screen-side counterpart, the 2UUL SA14PS Screen Sealing Adhesive for iPhone 14 Plus, so the front and the back of the same phone both get a fresh seal. Technicians who also stock soldering stations, reballing kits, and test boxes get a complete iPhone 14 Plus workflow from one catalog. Mechanicpk lists the 2UUL BA14PS in the mobile repair accessories range for professional benches, service centers, and training workshops.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut double-sided sealing adhesive for the iPhone 14 Plus back cover
- ✓Model-specific BA14PS code for the iPhone 14 Plus
- ✓Five pieces per pack for multiple repairs
- ✓Listed piece size of 145 x 70 x 0.5 mm
- ✓Part of the 2UUL BA series, which covers iPhone 14 to iPhone 17 models
- ✓Bonds under a heating press such as the 2UUL DA07 Mini Hot Press Station
- ✓Designed to restore the airtight seal on the iPhone frame
- ✓Suits technicians, repair shops, and service centers
Specifications
| Brand | 2UUL |
|---|---|
| Model | BA14PS |
| Category | Mobile Repair Accessories – Back Cover Adhesive |
| Compatibility | Apple iPhone 14 Plus |
| Technology | Pre-cut double-sided sealing adhesive |
| Dimensions | 145 x 70 x 0.5 mm |
| Pack Quantity | 5 pcs per pack |
Common Repair Uses
- ✓Resealing the rear glass of an iPhone 14 Plus after the back opens
- ✓Back glass replacement on the iPhone 14 Plus
- ✓Resealing the back cover after a battery replacement
- ✓Closing the phone after a charging issue repair
- ✓Resealing after speaker or internal module work
- ✓Closing the back after logic board and hardware fault repair
- ✓Bonding the adhesive with a heated press to restore the airtight seal
Compatible Devices
- ✓Apple iPhone 14 Plus (model-specific part)
- ✓Apple iPhone 14 Plus back cover / rear glass resealing
- ✓Model-specific BA14PS code: sized for the iPhone 14 Plus only
- ✓Other iPhone models need their own 2UUL BA-series code



