2UUL BA17PM Back Cover Sealing Adhesive iP17 Pro Max
₨ 900
iPhone 17 Pro Max Back Cover Sealing Adhesive
The 2UUL BA17PM Back Cover Sealing Adhesive for iP17 Pro Max (5pcs/Pack) gives your repair bench a pre-cut, double-sided seal made for the iPhone 17 Pro Max rear glass. When you open the back cover for a battery swap, charging port job, or board-level repair, this iPhone 17 Pro Max back cover sealing adhesive closes the housing again and restores the airtight fit the frame needs. Each pack holds five pieces, so one box covers five resealing jobs. The BA17PM code matches the Pro Max frame only, so you pick the right variant before you open the pack. Mechanicpk supplies it to Pakistani repair professionals.
In stock
2UUL BA17PM: Pre-Cut Sealing Adhesive Built for the iPhone 17 Pro Max Back Glass
The 2UUL BA17PM Back Cover Sealing Adhesive for iP17 Pro Max (5pcs/Pack) is an iPhone 17 Pro Max back cover sealing adhesive that replaces the original bond after you open the rear glass. 2UUL builds its BA series as pre-cut, double-sided adhesive for the iPhone 14 to 17 range, and the BA17PM code marks the cut for the 17 Pro Max frame. You peel, position, and press instead of trimming tape by hand, so the seal follows the frame outline on every job. Any technician who handles back glass replacement or internal repair on this model needs fresh adhesive, because the old bond does not survive removal.
Key Technical Highlights
Each piece in the pack is a double-sided adhesive frame that sits between the housing and the rear glass. 2UUL designs the BA series for repairing poor back cover seals and for fitting a replacement back cover, and the thermal sealing step restores the airtight closure of the housing. The BA17PM code applies to the iPhone 17 Pro Max only. 2UUL lists separate codes for the iPhone 17 (BA17), iPhone 17 Pro (BA17P), and iPhone Air (BA17A), so you match the code to the phone before you start. The pack contains five pieces, which equals five finished resealing jobs for a shop that sees steady Pro Max traffic.
Repair Workflow Fit
Back cover adhesive comes at the end of the job. You heat the rear glass to soften the old bond, cut around the edges, lift the glass, and finish the internal work first, whether that is a battery swap, a charging issue repair, or a hardware fault diagnosis on the logic board. Apple’s own service procedure for this phone follows the same order: heat, open, clean, then apply replacement adhesive. Clean the frame and the glass edge with IPA or ethanol until no residue remains, and inspect the frame for deformation before you lay the new adhesive.
Your existing bench tools cover the other stages. A hot air station set to a controlled temperature, or a heated fixture, handles the opening stage. A microscope helps you check the frame edge for leftover adhesive, and a PCB holder keeps the board steady while you work inside the phone. Residue under a new adhesive weakens the seal, so the cleaning step decides how well the result holds.
Why Technicians Choose the BA17PM
A shop that reseals iPhone back glass needs fit before anything else. Pre-cut adhesive removes the trimming step, cuts waste, and keeps the cutouts aligned with the frame. Reseller listings describe the BA series as high-adhesion double-sided adhesive built for stable long-term use. 2UUL also offers matching screen sealing adhesive codes such as SA17PM for the display side, so you can handle the display and the back cover with one brand. For the pressing stage, 2UUL makes the DA68 thermal plate for the iPhone 17 Pro and 17 Pro Max back cover, which speeds sealant curing during hot pressing.
Test the phone after reassembly. Power it on, check charging, and confirm the display responds before you hand it back to the customer. If you run a repair shop, service center, or training institute in Pakistan, the 5-piece pack gives you a clean, repeatable way to finish every iPhone 17 Pro Max back glass job. Mechanicpk stocks it for technicians who want a precise, model-specific part instead of generic tape.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut double-sided adhesive designed for the iPhone 17 Pro Max back cover
- ✓BA17PM model code matches the Pro Max frame outline
- ✓Restores the airtight seal after back glass removal
- ✓High-adhesion double-sided construction for stable long-term hold
- ✓Five pieces per pack for five resealing jobs
- ✓No hand trimming before application
- ✓Fits both back cover replacement and resealing of an existing back glass
- ✓Part of the 2UUL BA series for iPhone 14 to 17 models
Specifications
| Brand | 2UUL |
|---|---|
| Model | BA17PM |
| Category | Back Cover Sealing Adhesive |
| Compatibility | iPhone 17 Pro Max |
| Supported Devices | iPhone 17 Pro Max |
| Technology | Pre-cut double-sided sealing adhesive (BA series) |
| Pack Quantity | 5 pieces per pack |
Common Repair Uses
- ✓Real-world resealing jobs after the back glass comes off
- ✓Resealing the housing after back glass removal
- ✓Fitting a replacement back cover on an iPhone 17 Pro Max
- ✓Repairing a poor back cover seal
- ✓Closing the phone after a battery replacement
- ✓Closing the phone after a charging port or charging issue repair
- ✓Resealing after a board-level hardware fault repair
Compatible Devices
- ✓Model-specific scope: iPhone 17 Pro Max only
- ✓iPhone 17 Pro Max rear glass and frame
- ✓Not for iPhone 17 (use BA17)
- ✓Not for iPhone 17 Pro (use BA17P)
- ✓Not for iPhone Air (use BA17A)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use the 2UUL BA17PM on other iPhone 17 models?
Do I need to clean the iPhone frame before applying the BA17PM adhesive?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



