2UUL DA29 Vajra Carbon Fiber Handle for Mobile Repair

₨ 900

Ultralight Carbon Fiber Repair Handle

The 2UUL DA29 Vajra carbon fiber handle gives your precision pry needles and blades a light, rigid grip for IC-level work. 2UUL builds it from ultralight carbon fiber, so your hand stays steady through long sessions of chip lifting, underfill glue removal and tin dragging on mobile and tablet motherboards. Mechanicpk supplies the DA29 to Pakistani technicians who already run fine-tip tools and want a more controlled holder for dead phone, charging issue and hardware fault boards. Pair it with a compatible 2UUL blade or needle set and your bench gets a precise, low-fatigue tool for daily rework.

In stock

10 People watching this product now!
Description

2UUL DA29 Carbon Fiber Handle for Precision Board Work

The 2UUL DA29 carbon fiber handle, sold under the Vajra name, gives your fine pry needles and repair blades a light, rigid grip for work at the IC level. 2UUL builds the DA29 around ultralight carbon fiber, so the tool stays weightless in your fingers while you lift chips, clear glue and drag tin on a mobile motherboard. Mechanicpk stocks it for technicians who already own precision tips and want a steadier holder for them. When your bench handles IC change karna jobs every day, the handle is the part your hand touches for hours, and it deserves the same attention as the tip itself.

Carbon Fiber Build and Hand Control

Carbon fiber gives the DA29 a stiff body at very low weight. That combination matters when you work under a microscope, where a heavy or flexing handle makes small movements harder to place. A rigid shaft transfers your finger pressure straight to the tip, so you feel the moment a pry needle meets resistance under a BGA edge. The weight also stays low enough that your wrist and fingers hold the position without strain. 2UUL’s own pry needle set built on this handle weighs only 22 g gross, which shows how light the whole tool runs.

Where It Fits in Your Repair Workflow

You use a handle like this in the middle of the board-level repair sequence. First you warm the board on a hot air station to soften solder and underfill. Then you work the pry needle around the chip edge, lift the IC, and clear leftover adhesive from the pads. You finish by dragging tin to level the pads before reballing or reflow. Technicians chasing a dead phone, a charging issue or a hang on logo fault caused by a damaged IC repeat this sequence all day, so a controlled grip directly affects how clean the result looks. The DA29 suits underfill glue removal, BGA IC lifting, edge adhesive cleaning and micro-solder control on mobile phone and tablet boards.

Matching the Handle with Your Blades and Bench Tools

2UUL sells its pry needle and blade sets in the DA29 handle format, and the SC88 IC micro-point pry needle set is one of them. 2UUL does not publish the blade interface for the handle on its own listing, so check the blade or needle set you plan to run before you order. Once you have the tip sorted, the handle slots into a normal repair bench. Hold the board in a PCB holder, heat it with your hot air station or soldering station, inspect pads under a microscope, and prepare them for a reballing kit. A multimeter then confirms the rails after you reinstall the chip. Each step in that chain depends on clean pad preparation, and the DA29 carbon fiber handle supports exactly that step.

Additional information
Weight0.10 kg
Q & A
Please login to post questions

Key Features

  • Ultralight carbon fiber construction
  • Vajra carbon composite design for rigid, direct tip control
  • Light weight that limits hand fatigue during long bench sessions
  • Fits 2UUL pry needle and blade sets built for the DA29 handle, including the SC88
  • Suited to mobile phone and tablet motherboard repair
  • Supports delicate point work under a microscope
  • Part of the 2UUL disassembly tool range
  • Built for daily use in repair shops and service centers

Specifications

Brand2UUL
ModelDA29 Vajra Carbon Handle
CategoryDisassembly Tools / Precision Repair Handles
Compatibility2UUL precision pry needle and blade sets built for the DA29 handle format, such as the SC88 IC micro-point pry needle set
MaterialUltralight carbon fiber

Common Repair Uses

  • Hands-on holding of precision pry needles and blades during board-level mobile repair.
  • BGA IC lifting and separation
  • Underfill glue and edge adhesive removal
  • Tin dragging and micro-solder joint smoothing
  • Pad cleaning before reballing
  • Chip lifting during IC change karna jobs
  • Board-level work on dead phone and charging issue faults

Compatible Devices

  • Universal handle for precision repair tools, not device-specific. It works on the boards of any phone or tablet you service with a matching tip.
  • Mobile phone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno, iPhone series), as supported by the tip you fit
  • Tablet motherboards
  • BGA IC packages on phone PCBs
  • Underfill-covered chips and edge-bonded ICs
  • Solder pads and tin bridges on small boards

FAQ

What is the product name?
The product name is 2UUL DA29 Vajra Carbon Handle.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is DA29.
What is this product used for?
This product holds precision pry needles and blades for IC lifting, underfill glue removal and tin dragging during mobile phone and tablet board repair.
Which devices are compatible with this product?
The handle is not device-specific. It works with any phone or tablet board you service, as long as you fit a matching 2UUL pry needle or blade set.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which 2UUL tools work with the DA29 carbon handle?
2UUL sells pry needle and blade sets in the DA29 handle format, and the SC88 IC micro-point pry needle set is one of them. Check the blade set listing before you order to confirm fit.
Is the DA29 handle good for removing IC glue on dead phone boards?
Yes. The handle holds fine pry needles for underfill glue and edge adhesive removal, and the carbon fiber build gives you stable control when you work around a BGA chip under a microscope.