YCS Camera Lens Cover Magnetic Protector
₨ 600
Magnetic Camera Lens Protector for Repair Work
The YCS Camera Lens Cover Magnetic Protector shields a phone’s camera lens while you heat, solder, or disassemble the device. The transparent cover holds on with magnetic adsorption, so you skip the sticker, keep the lens visible under the microscope, and reuse the cover on the next job. YCS lists it as high-temperature resistant for heating and soldering repairs on iPhone and Android phones. You pick the rear, front, or Android variant to match your bench, then pair the cover with your hot air station and soldering station for cleaner board-level work in your Pakistani repair shop.
In stock
Magnetic Camera Lens Protector Built for Board-Level Repair
The YCS Camera Lens Cover Magnetic Protector is a magnetic camera lens protector that sits over a phone’s camera lens while you heat, solder, or open the device. YCS positions it as a transparent, high-temperature-resistant cover that replaces camera stickers on iPhone and Android repairs. If your bench handles back glass jobs, charging issue repairs, or board-level work with the camera module still installed, this cover gives the lens a physical shield instead of a strip of adhesive. Mechanicpk supplies it to Pakistani repair shops and service centers that want a reusable alternative to disposable lens stickers.
How the Magnetic Adsorption Design Works
The cover attaches by magnetic adsorption, so you set it on the lens ring and it holds without glue. That matters on a busy bench, where every sticker you peel risks leaving residue or lifting at the edge once hot air blows across it. The transparent body lets you see the lens, so you confirm placement under the microscope before you start. YCS describes the material as high-temperature resistant and built for heating and soldering repairs. The listing gives no temperature rating, so keep your hot air settings and nozzle distance where you normally run them. When the job ends, lift the cover off with your tweezers and reuse it on the next phone. The product is a cover only and does not include a camera module.
Where It Fits in Your Repair Workflow
Heat and flux near the camera are the risks this cover addresses. You place it before you start back glass separation, charging port work near the camera flex, or logic board repair on a dead phone that still carries its camera modules. Set up your PCB holder, cover the lens, and work under your soldering station or hot air station as usual. The step takes seconds, and it gives you a consistent habit across every phone you open, whether the job is a hardware fault, a display problem, or a boot loop issue that sends you into the board. Keep the covers in the same tray as your tweezers so the step happens on every job instead of becoming a judgment call.
Choosing the Right Cover Variant
YCS sells this cover family in several variants: a rear camera cover for iPhone dual and single camera layouts, a front camera diamond cover, and an Android camera protector. Match the variant to the phone on your bench before you order. The YCS listing for this product points at the iPhone 13, 14, 15, and 16 series, and the Android variant covers brands such as Samsung, Xiaomi, Huawei, Vivo, and OnePlus. Build the rest of your lens-safe setup around it with hot air stations, soldering stations, microscopes, and PCB holders, then add reballing kits and multimeters when the repair goes deeper into the board.
| Weight | 0.10 kg |
|---|
Key Features
- ✓Magnetic adsorption holds the cover on the lens ring without adhesive
- ✓Transparent body keeps the lens visible while you work
- ✓High-temperature-resistant construction for heating and soldering repairs
- ✓Replaces disposable camera stickers with a reusable cover
- ✓Rear, front, and Android variants within the YCS cover family
- ✓Removes with tweezers when the repair ends
- ✓Suits iPhone and Android camera lens protection
- ✓Cover only, so it carries no camera module and fits cleanly into a tool tray
Specifications
| Brand Entity | YCS |
|---|---|
| Product Entity | YCS Camera Lens Cover Magnetic Protector |
| Technology Entity | Magnetic adsorption, high-temperature-resistant transparent cover |
| Compatible Device Entities | iPhone 13, 14, 15, 16 series; Samsung, Xiaomi, Huawei, Vivo, OnePlus (Android variant) |
| Repair Process Entity | Camera lens protection during hot air and soldering repair |
| Industry Entity | Mobile phone repair accessories, Pakistan |
Common Repair Uses
- ✓Protecting the camera lens while you heat or solder near the camera module.
- ✓Back glass separation with a hot air station
- ✓Soldering near the camera flex connector
- ✓Charging port repair on phones with the camera still installed
- ✓Logic board repair on a dead phone with camera modules in place
- ✓Hot air rework near the camera area
- ✓Replacing camera stickers on the bench
- ✓Keeping the lens covered during disassembly and reassembly
- ✓Camera-area repair work under a microscope
Compatible Devices
- ✓iPhone and Android phone camera lenses. Fit depends on the cover variant you choose.
- ✓iPhone 13 series
- ✓iPhone 14 series
- ✓iPhone 15 series
- ✓iPhone 16 series
- ✓Samsung (Android variant)
- ✓Xiaomi (Android variant)
- ✓Huawei (Android variant)
- ✓Vivo (Android variant)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can this cover protect the camera during hot air work?
Does this cover work on Android phones or only iPhone?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



