Qianli Bumblebee Stencil (QS44) SAM5 for Samsung S10 Note10
₨ 799
Samsung S10 and Note10 CPU Reballing Stencil
The Qianli Bumblebee Stencil (QS44) SAM5 gives repair technicians a ready match for Samsung Galaxy S10, S10 Plus and Note10 boards. Qianli lists it for model numbers G9730, G975, G977 and N975, covering both the Exynos 9820 and Snapdragon 855 (SM8150) processors. You place it over the CPU pads, apply solder, and reball with the correct hole layout the first time. Pair it with your hot air station, flux and microscope for clean CPU rework on dead phone and hardware fault boards. Order the QS44 from Mechanicpk and keep a dedicated S10 generation stencil on your bench.
In stock
Samsung S10 Note10 Reballing Stencil for Exynos 9820 and Snapdragon 855 Boards
The Qianli Bumblebee Stencil (QS44) SAM5 is a Samsung S10 Note10 reballing stencil built for boards that carry the Exynos 9820 or the Snapdragon 855 (SM8150) processor. Qianli lists it for the Galaxy S10, S10 Plus and Note10 series, with model numbers G9730, G975, G977 and N975, under its CPU universal series. You use it at the moment a CPU comes off the board and goes back on with fresh solder balls, so the hole pattern has to match the chip exactly. QS44 gives you that match for the S10 generation without guesswork, and it keeps your Samsung rework consistent from one board to the next, whether you run a single repair bench or a busy service centre.
Where QS44 fits in your CPU reballing workflow
A stencil job starts after the CPU is off the board. You lift the chip with your hot air station, clean the old solder from the pads, and check the pad surface under a microscope. Next you line up the stencil edges with the pad field, hold it steady, then align the QS44 openings over the pads, fill them with solder paste or balls, and apply controlled heat until the balls form. The stencil does one job in that sequence, and it decides whether every ball lands in the right position. On a Samsung flagship board with tight pad spacing, a stencil made for the exact chipset saves you from lifting pads and repeating the work. Work in good light and use a PCB holder to keep the board flat and still, and keep flux on hand for the cleanup passes. After the reball, inspect the result under magnification and check for shorts with your multimeter before you power the board.
Exynos 9820 and Snapdragon 855 coverage in one stencil
Samsung built the S10 range around two different processors depending on the region. QS44 covers both the Exynos 9820 and the Snapdragon 855 (SM8150), so you do not need separate stencils for the two variants of the same phone. Check the board marking and the model number before you order. The listed numbers G9730, G975, G977 and N975 give you a quick reference when a customer hands you a phone with no readable model sticker. If your board belongs to another Samsung generation, choose the Bumblebee stencil numbered for that generation. Qianli sells separate numbers for families such as the S6 and the S8, and mixing them up wastes a CPU. As your workshop grows, add the matching Bumblebee numbers for each generation you service and keep them labelled in one tray.
Bumblebee design and the bench setup around it
The Bumblebee range uses square holes with rounded angles, and Qianli describes the stencils as sturdy, precise and durable over time. Treat QS44 like any fine metal template, because a bent edge or a clogged opening ruins the next reball. Keep it flat, clean the openings after each job, and store it apart from other stencils so the holes stay undamaged. QS44 handles ball placement, and the rest of the job depends on your equipment. A hot air station sets the reflow profile, a soldering station cleans the pads, and a microscope lets you inspect each ball before you refit the chip. Mechanicpk also stocks reballing kits, PCB holders, multimeters and test boxes, so you can build the full Samsung flagship setup from one order and move from a basic stencil kit toward a more complete BGA rework line as your volume grows. Technicians reach for this stencil on dead phone and boot loop boards once the fault traces back to CPU solder joints, and on any hardware fault where a replacement CPU needs fresh balls before fitting. Buyers checking the Qianli Bumblebee Stencil (QS44) SAM5 price in Pakistan will find the current store price on this page.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Dedicated QS44 hole layout for Samsung Galaxy S10, S10 Plus and Note10 boards
- ✓Covers both Exynos 9820 and Snapdragon 855 (SM8150) variants
- ✓Lists four model numbers for quick checks: G9730, G975, G977, N975
- ✓Square holes with rounded angles from the Qianli Bumblebee series
- ✓Part of Qianli’s CPU universal series stencil range
- ✓Numbered by generation, so you match the stencil to the board without guessing
- ✓Works in a hot air reballing workflow alongside flux and a PCB holder
- ✓Pairs with reballing kits, microscopes and multimeters for a complete CPU rework setup
Specifications
| Brand Entity | Qianli (Bumblebee stencil series) |
|---|---|
| Product Entity | Qianli Bumblebee Stencil (QS44) SAM5 |
| Technology Entity | BGA reballing stencil, square-hole round-angle design |
| Compatible Device Entities | Samsung Galaxy S10, S10 Plus, Note10 series; Exynos 9820; Snapdragon 855 (SM8150) |
| Repair Process Entity | CPU reballing, BGA rework, PCB repair |
| Industry Entity | Mobile phone repair, GSM repair workshops Pakistan |
Common Repair Uses
- ✓CPU reballing and rework on Samsung S10-generation boards
- ✓CPU reballing on Galaxy S10 boards
- ✓CPU reballing on Galaxy S10 Plus boards
- ✓CPU reballing on Galaxy Note10 series boards
- ✓Exynos 9820 CPU ball replacement after chip removal
- ✓Snapdragon 855 (SM8150) CPU reballing
- ✓Reballing a replacement CPU before fitting it to the board
- ✓Rework on dead phone boards where CPU solder joints are the suspect
- ✓Pad alignment and ball placement checks after cleanup
Compatible Devices
- ✓Samsung S10-generation boards (Exynos 9820 and Snapdragon 855 SM8150)
- ✓Samsung Galaxy S10
- ✓Samsung Galaxy S10 Plus
- ✓Samsung Galaxy Note10 series
- ✓Model G9730
- ✓Model G975
- ✓Model G977
- ✓Model N975
- ✓Exynos 9820 and Snapdragon 855 (SM8150) CPU boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which chipsets does the Qianli QS44 stencil support?
Can I use QS44 on a Galaxy S9 or S20 board?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock


