Qianli Dot Projector Precision Calibrator For iPhone 11
₨ 5,999
Face ID Dot Projector Calibrator for iPhone 11 Series
The Qianli Dot Projector Precision Calibrator For iPhone 11 / 11P / 11PM gives you a fast, repeatable way to align the Face ID dot projector module during iPhone 11, 11 Pro and 11 Pro Max repairs. The high-hardness aluminium alloy body carries a hole layout for the front camera, infrared camera and dot projector, and magnets secure the module while you work. Use this Qianli dot projector calibrator for iPhone 11 to standardise Face ID alignment on your repair bench and cut down on misaligned modules and repeat jobs.
In stock
Qianli Dot Projector Calibrator for iPhone 11 Series Face ID Repair
The Qianli Dot Projector Precision Calibrator For iPhone 11 / 11P / 11PM is a Face ID repair fixture for the iPhone 11, iPhone 11 Pro and iPhone 11 Pro Max. If you search for a Qianli dot projector calibrator for iPhone 11, you want one thing from the tool: a repeatable way to seat the dot projector module in exactly the right place before you close the board up. Qianli builds this fixture from high-hardness aluminium alloy and cuts it to the iPhone 11 series layout, so the module sits where the factory placed it and your Face ID repair does not rely on guesswork.
How the fixture positions the dot projector
Face ID depends on the dot projector, the infrared camera and the front camera sitting in a precise relationship to each other. A small shift in the dot projector flex cable or its components is enough to trigger the “Move iPhone a little lower” prompt during Face ID setup. This calibrator carries cutouts for the front camera, the infrared camera and the dot projector, and the base holes line up the flex cable with those openings. The fixture locks the module in place with magnets, so it holds position while you work instead of drifting under tweezers or a hot air nozzle. You get a fast fixation step that takes seconds, not a trial-and-error alignment on every board.
Where it fits in your iPhone 11 Face ID workflow
A typical dead Face ID job on an iPhone 11 splits into two parts: the data side and the physical side. A repair programmer reads and writes the dot projector flex cable data, and this calibrator handles the alignment of the module once the new or repaired part goes back into the phone. Pair it with a quality microscope so you can check the flex cable edges against the fixture holes, and keep a PCB holder on your bench to steady the logic board. If your job also involves reballing or lifting nearby components, your hot air station and reballing kit stay in the same workflow, and the calibrator protects the module position while you do it. Multimeter checks on the front sensor lines belong before you commit to the fixture step, so you know the fault sits in the dot projector assembly and not elsewhere on the board.
Why technicians in Pakistan choose a dedicated fixture
Repair shops in Pakistan handle a steady flow of iPhone 11 units, and Face ID complaints rank among the most common hardware fault jobs on that model. A dedicated alignment fixture turns a fiddly manual step into a standard one. Whoever on your team picks up the job gets the same positioning result, which keeps your comeback rate low and your turnaround predictable. The aluminium alloy body resists the wear that plastic jigs pick up after a few hundred uses, and one fixture covers all three iPhone 11 models, so you buy once instead of stocking a separate holder per variant.
Scope and limits you should know
This version targets the iPhone 11 series only. Qianli lists separate calibrators for the iPhone X, XS and XR family and for the iPhone 12 series, so match the fixture to the model on your bench. The calibrator solves alignment. It does not read or write dot projector data, and it does not repair a damaged projector chip, so keep your programmer in the kit for that part of the job. Treat the dot projector parts with care, since a drop or water damage can harm them, and use the fixture as the final positioning step in a complete Face ID repair routine. Pair it with the rest of your Face ID tooling and you cover the full iPhone 11 front-sensor repair chain from diagnosis to final alignment.
| Weight | 0.30 kg |
|---|
Key Features
- ✓Fast fixation that seats the dot projector module in seconds
- ✓High-hardness aluminium alloy body
- ✓Precise positioning aid for the Face ID module
- ✓Hole cutouts for the front camera, infrared camera and dot projector
- ✓Base holes that line up the dot projector flex cable
- ✓Magnet-secured fixture that holds position during the job
- ✓One fixture for iPhone 11, 11 Pro and 11 Pro Max
- ✓Standard positioning that reduces alignment errors from job to job
Specifications
| Brand Entity | Qianli |
|---|---|
| Product Entity | Qianli Dot Projector Precision Calibrator For iPhone 11 / 11P / 11PM |
| Technology Entity | Face ID dot projector, infrared camera, magnetic positioning fixture |
| Compatible Device Entities | iPhone 11, iPhone 11 Pro, iPhone 11 Pro Max |
| Repair Process Entity | Face ID dot projector flex cable alignment |
| Industry Entity | Mobile phone repair, iPhone board-level repair |
Common Repair Uses
- ✓Face ID dot projector alignment on the iPhone 11 series
- ✓Aligning the dot projector flex cable during Face ID repair
- ✓Seating a new or repaired dot projector module in the correct position
- ✓Fixing the "Move iPhone a little lower/higher" Face ID setup error after the part is replaced
- ✓Holding the front camera, infrared camera and dot projector openings in line
- ✓Standardising Face ID alignment across every iPhone 11 job in your workshop
Compatible Devices
- ✓Verified scope: iPhone 11 series
- ✓iPhone 11
- ✓iPhone 11 Pro
- ✓iPhone 11 Pro Max
FAQ
What is the product name?
What is the brand of this product?
What is this product used for?
Which devices are compatible with this product?
What material is this calibrator made of?
Who should use this product?
Can I use this calibrator on an iPhone 12 or iPhone X?
Does this calibrator replace a Face ID repair programmer?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



