Back to products
Sunshine P-3005D 5A 30V DC Power Supply
Sunshine P-3005D 5A 30V DC Power Supply Original price was: ₨ 18,000.Current price is: ₨ 15,500.

Qianli Dot Projector Precision Calibrator For iPhone 12

₨ 6,300

Dot Projector Calibrator for iPhone 12 Series

The Qianli Dot Projector Precision Calibrator For iPhone 12 / 12P / 12PM / 12M is a Face ID repair fixture that holds the dot projector in position while you work on an iPhone 12 series board. It covers the iPhone 12, 12 mini, 12 Pro and 12 Pro Max, so one fixture serves every model in the range. You get fast fixation and a precise positioning aid, which cuts the trial-and-error of aligning a small module by hand. Repair shops and service centers that handle Face ID faults on 12 series phones can use it as a dedicated bench fixture next to their microscope and soldering setup.

In stock

17 People watching this product now!
Description

Dot Projector Precision Calibrator for iPhone 12 Face ID Repair

The Qianli Dot Projector Precision Calibrator For iPhone 12 / 12P / 12PM / 12M does one job: it holds the Face ID dot projector in the correct position during repair on an iPhone 12 series phone. A dot projector precision calibrator for iPhone 12 matters because the module is small, the tolerance is tight, and a module aligned by eye gives you inconsistent results. Mechanicpk supplies this fixture for technicians who treat Face ID as a repeatable repair process, not a gamble.

Where the Fixture Fits in a Face ID Repair

Face ID repair on the iPhone 12 series follows a clear sequence: you diagnose the fault, separate the dot projector assembly, repair or replace the affected part, and then set the module back in its working position. The calibrator supports that last stage. Qianli describes this fixture line as a lattice and dot matrix alignment tool, and its fast fixation holds the assembly steady so your hands stay free for the actual repair. You work on one fixed reference instead of balancing a loose module under the microscope.

This role makes the fixture useful on jobs where the phone shows a Face ID error, a dead Face ID after a screen or front camera swap, or a damaged dot projector flex cable. Each of those repairs ends with the same question: is the module sitting where it should? A positioning aid answers that question at the bench, before you reassemble the phone.

Fit Across the iPhone 12 Family

This version of the Qianli dot projector calibrator targets the whole iPhone 12 range: iPhone 12, iPhone 12 mini, iPhone 12 Pro and iPhone 12 Pro Max. The product name abbreviates these as 12, 12P, 12PM and 12M, so a single purchase covers the four models you see most often on a Pakistani repair counter.

Qianli sells separate versions of this fixture for the iPhone X, XS, XS Max, XR series and for the iPhone 11 series. Check the generation before you order. This listing serves the 12 series only, and it does not replace the other versions if your workshop also repairs older Face ID phones.

Bench Setup and Supporting Tools

A calibrator works best inside a complete Face ID workflow. Pair it with a good microscope for inspecting the module and flex connector, and a stable PCB holder to keep the logic board still while you work. If the fault sits on the board itself, your soldering station and hot air station handle the rework, and a multimeter confirms the circuit before you close the phone. Technicians who also run IC and reballing jobs can keep the fixture within reach of their reballing kit, since the two often appear on the same repair ticket.

This fixture is a positioning tool. It is not a programmer, and it does not replace the flex and chip data work that some Face ID repairs need. You use it to place the module correctly, and you use your other equipment for the electrical and software side. Treating each tool as one clear step keeps your repair process organized and your results consistent from one job to the next.

Additional information
Weight0.30 kg
Q & A
Please login to post questions

Key Features

  • Fast fixation of the dot projector assembly
  • Precise positioning aid for Face ID alignment
  • Covers iPhone 12, 12 mini, 12 Pro and 12 Pro Max in one fixture
  • Dedicated Face ID dot projector repair tool for 12 series boards
  • Frees both hands for repair work
  • Fits a microscope, PCB holder and soldering workflow

Specifications

BrandQianli
CategoryFace ID Dot Projector Repair Fixture
CompatibilityiPhone 12 series
Supported DevicesiPhone 12, iPhone 12 mini, iPhone 12 Pro, iPhone 12 Pro Max

Common Repair Uses

  • Face ID dot projector repair on iPhone 12 series phones
  • Holding the dot projector during Face ID repair
  • Positioning the module after a front camera or screen related repair
  • Face ID not working after dot projector replacement
  • Dot projector flex cable repair and re-seating
  • Fixing a dot projector that sits out of position
  • Bench alignment check before reassembly

Compatible Devices

  • iPhone 12 series (version-specific, not for other generations)
  • iPhone 12
  • iPhone 12 mini
  • iPhone 12 Pro
  • iPhone 12 Pro Max

FAQ

What is the product name?
The product name is Qianli Dot Projector Precision Calibrator For iPhone 12 / 12P / 12PM / 12M.
What is the brand of this product?
The brand of this product is Qianli.
What is this product used for?
This product holds and positions the Face ID dot projector during iPhone 12 series repair.
Which devices are compatible with this product?
This product is compatible with the iPhone 12, iPhone 12 mini, iPhone 12 Pro and iPhone 12 Pro Max.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What does 12P, 12PM and 12M mean in the product name?
They stand for iPhone 12 Pro, iPhone 12 Pro Max and iPhone 12 mini, so the fixture covers all four iPhone 12 models.
Does this fixture also fit iPhone X, XS, XR, 11 or 13 models?
No. This version targets the iPhone 12 series only. Qianli sells separate versions for the iPhone X to XR series and the iPhone 11 series.
Does this calibrator replace a Face ID programmer?
No. It is a positioning fixture for the dot projector. Flex and chip data work needs separate programming equipment.