Mechanic V4B45 138°C Low Temp Solder Paste 40g Syringe

₨ 1

138°C Low Temp Solder Paste for Heat-Sensitive Board Work

The Mechanic V4B45 is a lead-free low temperature solder paste with a Sn42Bi58 alloy that melts at 138°C. You get a 40g syringe with IPX4 flux already in the formulation, which gives controlled dispensing for pads, jumpers and reballing points. The lower melting point lets you complete a joint without pushing a heat-sensitive board through a hotter process. Use it at your repair bench for chip reattachment, jumper lagana work, and touch-up soldering where standard higher-temperature paste would stress nearby components. Forty grams gives a steady supply for daily repair volume at a single bench.

Out of stock

14 People watching this product now!
Description

Mechanic V4B45 138°C Low Temp Solder Paste 40g Syringe

The Mechanic V4B45 is a 138°C low temp solder paste built for technicians who need a joint that forms at lower heat than standard lead-free pastes. It is a lead-free formula with a Sn42Bi58 alloy, supplied in a 40g syringe with IPX4 flux already mixed in. On a repair bench, a low melting point gives you direct control over boards and chips that cannot handle long exposure to high temperature. This paste fills the gap between general-purpose tin pastes and the delicate work where thermal stress decides whether the board survives. Matching the alloy to the board, rather than forcing a hotter process onto every repair, is the core reason to keep a 138°C paste in your kit. The sections below explain the thermal logic, the alloy, and how the syringe fits your daily workflow.

Why a 138°C Melting Point Changes Your Heat Profile

Most reflow and reballing work uses far hotter alloys, and that heat travels into neighboring components, flux residue, and the layers of a multilayer board. A paste that melts at 138°C lets you lower the peak temperature your hot air or iron must reach, which reduces the thermal load across the whole area. You still get proper wetting on the pads, so the joint forms without the extra heat that can lift a trace or soften a nearby IC. This matters most when you are doing a chip reattachment or a delicate jumper where a hotter joint could damage the work you just completed. Set your station to the lowest temperature that still flows the paste, and check the joint under the microscope before you move to the next point. A low melting point does not excuse poor heat control, so keep dwell time short and watch the board edges.

Sn42Bi58 Alloy and What the Composition Means

The V4B45 uses a Sn42Bi58 alloy, which means roughly 42 percent tin and 58 percent bismuth by weight. Bismuth is the element that pulls the melting point down toward 138°C, while the formula remains lead-free. This composition suits low-temperature joints on boards and components that cannot withstand a hotter process, and the lead-free formula suits repair shops that avoid leaded solder. Bismuth-rich joints tend to be more brittle than tin-rich ones, so avoid flexing a finished joint and keep the paste away from areas that see repeated mechanical stress. Treat this alloy as a precision low-heat material rather than a structural solder for high-load connections. Your choice of alloy should always follow the thermal tolerance of the board in front of you.

Syringe Dispensing and IPX4 Flux Handling

The 40g syringe gives you controlled dispensing, so you place paste exactly where the joint needs it instead of spreading it across a pad. Press the plunger gently and load only the amount the work requires, because a surplus deposit is the most common cause of bridging on fine-pitch points. The IPX4 flux is already part of this formulation, so it supports wetting as the paste heats and helps keep the joint clean. Wipe the tip after each use, since cured flux inside the bore will block the next dispense. Store the syringe capped between sessions so the paste does not dry out and change its flow behavior. When you finish a job, check that the joint is bright and full, which tells you this 138°C low temp solder paste flowed correctly.

Additional information
Weight0.4 kg
Q & A
Please login to post questions

Key Features

  • Lead-free Sn42Bi58 alloy with a 138°C melting point
  • 40g quantity in a syringe applicator
  • IPX4 flux included in the formulation
  • Low-temperature profile for heat-sensitive boards and components
  • Controlled dispensing from the syringe
  • Suited to chip reattachment and jumper work
  • Pad touch-up and reballing on low-heat substrates
  • Lead-free formula for repair shops that avoid leaded solder

Specifications

BrandMechanic
ModelV4B45
CategorySolder Paste
CompatibilityUniversal — not device-specific
TechnologyLead-free low-temperature solder paste, 138°C melting point, syringe packaging
MaterialSn42% / Bi58% alloy with IPX4 flux

Common Repair Uses

  • Chip reattachment on mobile logic boards where high heat is a risk
  • Jumper wire installation on heat-sensitive motherboards
  • Low-temperature BGA reballing on delicate ICs
  • Pad touch-up and reflow on sensitive PCB areas
  • Trace repair on multilayer boards with limited thermal tolerance
  • Component reseating on boards with nearby heat-sensitive parts
  • Lifted pad repair where a hotter joint would lift adjacent copper
  • Low-heat soldering on special or non-standard substrates

Compatible Devices

  • Universal scope, not tied to a verified device model list
  • Lead-free Sn42Bi58 low-temperature alloy with a 138°C melt point
  • Mobile logic boards at the component level, including chip and jumper points
  • Multilayer PCBs where a lower reflow temperature is needed
  • BGA and chip reballing on heat-sensitive boards
  • General electronics PCB rework with low-heat joint requirements
  • Components with limited heat tolerance
  • Pad touch-up and trace repair on sensitive boards
  • Syringe applicator for controlled dispensing on repair benches

FAQ

What is the product name?
The product name is Mechanic V4B45 138°C Low Temp Solder Paste 40g Syringe.
What is the brand of this product?
The brand of this product is Mechanic.
What is the model of this product?
The model of this product is V4B45.
What is this product used for?
This product is used for low-temperature lead-free soldering on PCBs and chips where a lower melting point reduces heat stress.
Which devices are compatible with this product?
This product is compatible with universal PCB and chip work; it is not tied to a verified device-specific list.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What is the melting point of this solder paste?
The melting point is 138°C, based on its Sn42Bi58 alloy composition.
What alloy is used in the Mechanic V4B45 solder paste?
It uses a lead-free Sn42Bi58 alloy, roughly 42 percent tin and 58 percent bismuth.