2UUL RS199 Red Skull Solder Paste 199°C 50g
₨ 1,100
2UUL RS199 Solder Paste 199°C
The 2UUL RS199 solder paste gives your repair bench a 199°C Red Skull tin paste in a 50g pack. You use it for BGA stencil reballing and for tinning pads on phone motherboards. The paste flows cleanly, leaves less residue, and resists oxidation, so joints stay bright and complete without false welding. Pair it with a hot air station, a reballing kit, and a microscope to rebuild solder balls on ICs you pulled from dead phones. A 199°C rating suits technicians who want a controlled, low-temperature reballing option in their paste range. The 50g pack covers repeated jobs across IC change, CPU reballing, and board rework in a busy workshop.
In stock
2UUL RS199 Solder Paste for BGA Reballing and Board Rework
The 2UUL RS199 solder paste brings a 199°C Red Skull tin paste to your bench in a 50g pack, built around stencil-based BGA reballing and pad tinning. Distributors list the paste for BGA stencil reballing, and the 199°C grade gives you a defined melting point to plan your rework profile around. If you handle IC change karna jobs daily, a dependable paste keeps your reballing results consistent from one board to the next.
Where the Paste Fits in Your Reballing Workflow
Reballing starts after you lift the IC and clean the pads. You then align a stencil over the BGA, spread the paste across the apertures, and heat the paste until it forms balls on each pad. The RS199 grade sits in that middle step. Fix the IC in a PCB holder, work under a microscope, and run your hot air station or preheater at a profile that matches the paste and the chip. Check the supplier pack for any handling guidance before you heat. After reflow, a multimeter check across the pads confirms continuity before you refit the IC on the board.
Verified Paste Characteristics Technicians Notice
The supplier listings for the Red Skull range describe the paste as free of false welding, low in residue, conductive, and resistant to oxidation. The same listings note that the paste resists cracking and tins easily. In practice, low residue means you spend less time cleaning flux off the board after rework, and easy tinning helps when you build uniform balls on small-pitch pads. Oxidation resistance matters when a jar stays open across several jobs in one shift.
Choosing the 199°C Grade in the Red Skull Range
2UUL sells the Red Skull paste in several melting points, including 138°C, 148°C, 183°C, and 199°C. Each grade targets a different rework preference, so you match the grade to your process rather than to a single universal setting. Pick the RS199 when you want the 199°C grade in your drawer next to your other solder paste tins, flux, and solder wick. A repair shop that runs both lower and higher grades gets flexibility when one job needs a different melting point than the last.
Stocking RS199 for a Professional Repair Workshop
Pakistani repair shops and service centers burn through paste on every reballing session, so a 50g pack lasts across many boards. Keep the jar next to your soldering station, reballing stencils, and hot air station so you reach it without breaking your workflow. Store it with the lid sealed between jobs to protect the paste from air exposure, and keep your tools clean so each application stays tidy. Mechanicpk supplies the 2UUL RS199 solder paste together with related soldering and rework equipment, so you build one complete reballing setup from a single source.
| Weight | 0.50 kg |
|---|
Key Features
- ✓199°C Red Skull grade
- ✓50g pack for repeated workshop use
- ✓Suited to BGA stencil reballing
- ✓No false welding
- ✓Less residue after reflow
- ✓Good conductivity
- ✓Oxidation resistance
- ✓Not easy to crack and easy to tin
Specifications
| Brand | 2UUL |
|---|---|
| Model | RS199 Red Skull |
| Category | Solder Tin Paste |
| Technology | Solder paste, 199°C grade |
| Weight | 50g |
Common Repair Uses
- ✓Real workshop scenarios where you apply this paste
- ✓BGA stencil reballing
- ✓IC change karna rework with fresh pad tinning
- ✓Rebuilding solder balls on a removed IC
- ✓Reflowing SMD components on a motherboard
- ✓Fixing false-welding or weak joints
- ✓Dead phone board rework
- ✓General motherboard soldering and tinning
- ✓Preparing pads before refitting an IC
Compatible Devices
- ✓Universal solder paste — not device-specific; works on any board where you reball or tin through a stencil
- ✓Universal solder paste, not locked to any phone brand
- ✓BGA ICs reballed through a stencil
- ✓SMD pads on phone motherboards
- ✓Pads that need fresh tinning after IC removal
- ✓General PCB tinning work
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the melting point of 2UUL RS199 solder paste?
Can I use 2UUL RS199 for BGA stencil reballing?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



