338S00770 Charging IC for iPhone 13 Series

₨ 600

Tigris Charging IC for iPhone 13

The 338S00770 is the Tigris charging and power management IC for the iPhone 13 series, covering iPhone 13, 13 mini, 13 Pro and 13 Pro Max. It controls charging behavior and USB connectivity, which makes it a key suspect in no-charge and fake-charging faults on these boards. Distributor listings identify it as 338S00770 or 338S00770-B0, and both markings refer to the same board position. Replace it at board level only after you have ruled out the charging port and battery faults. Confirm the marking before fitting.

17 People watching this product now!
Description

338S00770 Charging IC for iPhone 13 Series Boards

The 338S00770 charging IC is the Tigris power management chip that controls charging and USB connectivity on the iPhone 13, iPhone 13 mini, iPhone 13 Pro and iPhone 13 Pro Max. Distributor listings show the marking as 338S00770 and 338S00770-B0, and both refer to the same board position. When a handset shows a dead phone or a charging issue, this IC sits in the charging path and belongs early in your diagnostic sequence. Technicians use it as a reference point when tracing a no-charge fault. The sections below cover fault patterns, bench workflow, and verification.

Fault Patterns That Point to This IC

The most common complaints tied to this part are no charging, fake charging, and heat near the charging port or logic board. Fake charging shows the charging icon while the battery percentage never rises, which usually means the charging path is not delivering current. Overheating during charge deserves a closer look at this area of the board. Before you desolder anything, rule out a damaged charging port, a shorted USB rail, and a faulty battery connector. Those three faults produce symptoms close to this IC, and a multimeter check confirms them faster than a rework does.

Compatibility Scope Across the iPhone 13 Series

This part is listed for the full iPhone 13 family: iPhone 13, iPhone 13 mini, iPhone 13 Pro, and iPhone 13 Pro Max. Verify the exact handset model before you order, because neighboring generations use different part numbers. Distributor listings for the iPhone 14 and iPhone 15 point to 338S00839 and 338S00946, so a mismatched part wastes time on the bench. Check the donor board’s model and marking first. Record the part number in your job card so the repair history stays traceable.

Bench Workflow for Removal and Replacement

This is a small surface-mount IC, so rework needs a stable hot air station, a microscope, and a PCB holder. Clean the old pads with flux and braid before you place the replacement, and inspect the pads under magnification for lifted or damaged copper. If you reball the chip before fitting, use a reballing kit matched to the package. Keep the board supported on a holder during heating so it does not warp. Work in short heat cycles, and recheck the pads with the microscope after each step.

Verifying the Board After Replacement

Confirm the replacement marking matches the original position before you power the phone. Once the board is live, check the charging input and confirm the phone detects the cable. A correct repair shows stable charging and no abnormal heat under normal load. Test with a known-good charger and cable, so the result reflects the board and not the accessory. Related ICs on the same board, including the 338S00817 wireless charging IC and the 343S00511 main power IC, can also cause charging symptoms, so check them when the first test is inconclusive. Pair this job with soldering stations, test boxes, and multimeters from the catalog for a complete bench setup.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Tigris power management IC for the iPhone 13 series
  • Manages charging behavior on compatible boards
  • Controls USB connectivity during charging
  • Covers iPhone 13, 13 mini, 13 Pro, and 13 Pro Max
  • Listed as 338S00770 or 338S00770-B0

Specifications

Model338S00770 (also listed as 338S00770-B0)
CategoryMobile Phone ICs, Charging IC
CompatibilityApple iPhone 13 series
Supported DevicesiPhone 13, iPhone 13 mini, iPhone 13 Pro, iPhone 13 Pro Max
TechnologyTigris power management IC

Common Repair Uses

  • Board-level charging faults on iPhone 13 series logic boards
  • No charging on a dead phone
  • Fake charging, where the icon shows but battery percentage does not rise
  • Overheating around the charging port or logic board during charge
  • Board-level IC replacement after port and battery faults are ruled out
  • Reballing and rework on a PCB holder under a microscope

Compatible Devices

  • iPhone 13 series (device-specific)
  • iPhone 13
  • iPhone 13 mini
  • iPhone 13 Pro
  • iPhone 13 Pro Max

FAQ

What is the product name?
The product name is 338S00770 Charging IC for iPhone 13 Series.
What is the model of this product?
The model is 338S00770, also listed as 338S00770-B0.
What is this product used for?
This product is a replacement charging and power management IC for board-level charging repair.
Which devices are compatible with this product?
This product is compatible with the iPhone 13, iPhone 13 mini, iPhone 13 Pro, and iPhone 13 Pro Max.
What symptoms show this IC has failed?
Common symptoms include no charging, fake charging where the icon appears without battery gain, and overheating around the charging port or logic board.
Is 338S00770 the same as 338S00770-B0?
Distributor listings use both markings for the same iPhone 13 charging IC position, so confirm the marking against the donor board before fitting.