2UUL BA17 Back Cover Sealing Adhesive for iP17 (5pcs/Pack)
₨ 900
iPhone 17 Back Glass Sealing Adhesive
The 2UUL BA17 Back Cover Sealing Adhesive for iP17 (5pcs/Pack) gives you five pre-cut double-sided sealing sheets for resealing the iPhone 17 back glass after a repair. Use it after a battery change, a charging port repair, or a cracked back glass swap, then press the glass down with a heating pressure press to bond it to the frame again. The BA17 code targets the standard iPhone 17 only, so Pro, Air, and Pro Max jobs need their own 2UUL codes. Mechanicpk stocks it for repair shops across Pakistan that want a consistent, model-matched seal on every iPhone 17 back cover.
In stock
iPhone 17 Back Cover Sealing Adhesive Made for Back Glass Resealing
The 2UUL BA17 Back Cover Sealing Adhesive for iP17 (5pcs/Pack) is an iPhone 17 back cover sealing adhesive built for one job: bonding the rear glass back to the frame after you open the phone. The factory adhesive never survives a back glass removal, so every iPhone 17 you open for a battery change, a charging issue, or a cracked back glass needs fresh adhesive before it closes. This pack gives you five pre-cut double-sided sealing sheets for the standard iPhone 17. You stock one model-matched consumable instead of trimming generic tape by hand, and you get a cleaner, more repeatable reseal on every job. Mechanicpk supplies the BA17 to repair shops and service centers that handle steady Apple volume.
Where the BA17 Fits in Your iPhone 17 Repair Workflow
Every iPhone 17 repair that starts at the back glass ends with the same step: new adhesive between the glass and the frame. You heat and cut the old bond, lift the glass, and finish the internal work, whether that is a battery change, a charging port repair, or a hardware fault check on the board. Before you close the phone, you clear the old residue from the frame and inspect the frame for deformation. Then you place the BA17 sheet on the frame, align the glass, and press it. 2UUL’s usage notes for its back cover adhesive range call for thermal sealing with a heating pressure press, and that step restores the airtightness of the back cover. A hot air station or heated removal fixture handles the opening stage, and a PCB holder keeps the board steady while you work inside the phone. The BA17 covers only the closing stage, which makes it the cheapest part of the job and the part that decides whether the customer comes back with a seal complaint.
Model-Specific Fit Across the 2UUL BA Range
2UUL numbers its back cover adhesives by iPhone model, and BA17 points at the standard iPhone 17. The iPhone 17 Pro takes BA17P, the iPhone Air takes BA17A, and the iPhone 17 Pro Max takes BA17PM. Check the code on the pack against the phone on your bench before you open the box, because a wrong-model sheet costs you a full reseal. The pre-cut shape follows the frame outline, so you skip trimming and you avoid the uneven edges that hand-cut tape leaves around the camera area and antenna bands. Shops that repair mixed iPhone 17 variants usually stock all four codes and shelve them by model. If your counter also sees iPhone 14 to 16 phones, 2UUL sells a separate back cover adhesive for that range, so you keep the same brand across generations.
Stocking Notes for Repair Shops and Service Centers
Each pack holds five sheets, so one pack covers five iPhone 17 back glass jobs at one sheet per job. That pack size suits a busy bench: you restock in small steps and you avoid tying up cash in a large adhesive inventory. Pair the BA17 with the 2UUL screen sealing adhesive when you open iPhone 17 phones from the front, and keep a microscope and fine tweezers within reach for residue cleanup on the frame. Order from Mechanicpk, keep a pack on the bench, and you stop turning away iPhone 17 back glass work because the adhesive ran out.
| Weight | 0.100 kg |
|---|
Key Features
- ✓Pre-cut double-sided sealing adhesive shaped for the iPhone 17 back cover and frame
- ✓Five sheets per pack for five back glass reseal jobs
- ✓Model-specific BA17 code for the standard iPhone 17
- ✓Restores the airtightness of the back cover after repair
- ✓Suits back cover replacement and repair of poor back cover seals
- ✓Applies with thermal sealing using a heating pressure press
- ✓Simple installation: clean the frame, check for deformation, align, and press
- ✓Belongs to the 2UUL BA range, with separate codes for iPhone 17 Pro, iPhone Air, and iPhone 17 Pro Max
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL BA17 Back Cover Sealing Adhesive |
| Technology Entity | Pre-cut double-sided sealing adhesive, thermal sealing with a heating pressure press |
| Compatible Device Entities | Apple iPhone 17 |
| Repair Process Entity | iPhone 17 back glass replacement and resealing |
| Industry Entity | Mobile phone repair, Apple repair consumables |
Common Repair Uses
- ✓iPhone 17 back glass replacement
- ✓Resealing the back cover after battery change
- ✓Resealing after charging port repair
- ✓Resealing after internal board or hardware fault inspection
- ✓Repairing a poor or failed back cover seal
- ✓Restoring back cover airtightness after any repair that removes the back glass
Compatible Devices
- ✓Verified scope: Apple iPhone 17 (standard model) only
- ✓Apple iPhone 17 (standard model)
- ✓Not for iPhone 17 Pro: use 2UUL BA17P
- ✓Not for iPhone Air: use 2UUL BA17A
- ✓Not for iPhone 17 Pro Max: use 2UUL BA17PM
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use the 2UUL BA17 on an iPhone 17 Pro, iPhone Air, or iPhone 17 Pro Max?
Do I need a heat press to fit the 2UUL BA17 back cover adhesive?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



