Mechanic CUV-3 UV Fan 3in1 Cooling & Curing Fan
₨ 2,900
3 in 1 UV Curing Fan for Repair Benches
The Mechanic CUV-3 UV Fan 3in1 puts a 395nm UV curing lamp, a three-speed cooling fan, and smoke extraction airflow into one cordless unit that measures 66 × 59 × 31 mm. You cure UV solder mask and UV adhesive, pull heat off a freshly reworked IC, and move soldering smoke away from your face without switching tools. Double SMD lamp beads, dual high-speed bearings, a two-gear timer, and a four-level power display give you control on every board. Repair shops and service centers across Pakistan can use it beside the soldering station and hot air station.
In stock
3 in 1 UV Curing Fan for Cooling, Curing, and Fume Control
The Mechanic CUV-3 UV Fan 3in1 replaces three separate bench accessories with one cordless unit. This 3 in 1 UV curing fan combines a 395nm violet lamp with double SMD beads, a three-speed cooling fan, and smoke extraction airflow inside a body that measures 66 × 59 × 31 mm. Mechanicpk supplies it to Pakistani technicians who run board-level repair every day and need a compact tool that sits beside the hot air station without crowding the bench. You get curing, cooling, and fume control from a single button panel, and you spend less time swapping tools between steps.
Curing and Cooling Performance for Board-Level Work
As a green oil curing lamp, the CUV-3 runs at 395nm, the wavelength that UV solder mask, which technicians call green oil, and UV optical adhesive respond to. After you rebuild a damaged track or scrape a pad clean, you apply fresh mask and cure it under the lamp instead of waiting for it to set unaided. Cure time depends on the mask or glue you use, so follow that product’s own instructions and test a small area first. The same lamp cures the UV glue that holds screen and component bonds. Double SMD lamp beads light the work area from a short distance, so you hold the unit close and keep both hands free for tweezers and a blade. At 66 × 59 × 31 mm, it fits between the microscope and the station without blocking your view. The fan gives you three speed levels, driven by dual high-speed bearings, with fan power levels of 1W, 1.3W, and 1.6W. After you reflow a charging IC or reball a chip, you pull heat off the board right away and move on to testing. That matters on charging issue and dead phone jobs, where heat soaking into neighbouring components creates a second hardware fault.
Cordless Controls, Battery, and Charging
A built-in rechargeable lithium battery turns the unit into a cordless UV curing lamp and fan, so no cable drags across your bench. It charges from a 5V input (±0.5V) at 480mA and takes 2 to 2.5 hours to fill. Four indicator levels, 25%, 50%, 75%, and 100%, show your remaining charge, so you know when to plug in before a long micro-soldering session. One-button shutdown, a two-gear timer, and three-gear speed control keep operation simple. Set the timer for a cure cycle and the unit tracks the time while you prep the next board. The compact body also travels in a toolbag, which helps technicians who visit customer sites. Keep the lamp pointed away from your eyes and skin whenever it runs, as you would with any UV source.
Where the CUV-3 Fits in Your Repair Workflow
Place the CUV-3 beside your soldering station and hot air station so the three tools share one working zone. During micro-soldering under a microscope, the fan moves smoke away from your face. After an IC replacement or reballing job, switch to cooling, then cure any UV mask you applied over repaired traces before the board goes back for testing. If you check boards on a test box, keep the CUV-3 within reach for a final cooling pass before power-on. A PCB holder keeps the board steady under the lamp, and a multimeter lets you confirm continuity once the mask cures. Repair shops that handle network issue, display problem, and charging issue boards all week gain the most from a 3 in 1 UV curing fan, because one unit covers heat control, fume control, and mask curing on every job. Training institutes and service centers benefit from the same layout, since students see the cooling, curing, and smoke steps happen in one place. If your volume grows, you can step up to a dedicated fume extractor with filtration or a larger curing lamp.
| Weight | 0.35 kg |
|---|
Key Features
- ✓3-in-1 design: cooling fan, UV curing lamp, and smoke extraction airflow
- ✓395nm violet lamp with double SMD lamp beads
- ✓Three-speed fan adjustment with dual high-speed bearings
- ✓Built-in rechargeable lithium battery for cordless use
- ✓Charges from a 5V input at 480mA in 2–2.5 hours
- ✓Four-level power display: 25%, 50%, 75%, 100%
- ✓One-button shutdown and two-gear timer
- ✓Compact 66 × 59 × 31 mm body
Specifications
| Brand | Mechanic |
|---|---|
| Model | CUV-3 |
| Category | UV Curing Lamp, Cooling Fan and Smoke Extraction Accessory |
| Compatibility | Universal, not device-specific |
| Supported Devices | Mobile phone, tablet, and laptop PCB repair |
| Technology | 395nm UV curing lamp with double SMD beads, dual high-speed bearing fan, built-in rechargeable lithium battery (480mA charging, 2–2.5 hours) |
| Input Voltage | 5.0V ± 0.5V (charging) |
| Power Rating | Fan power levels 1W / 1.3W / 1.6W |
| Dimensions | 66 × 59 × 31 mm |
Common Repair Uses
- ✓Curing UV solder mask (green oil) after track or pad repair
- ✓Curing UV adhesive for screen and component bonding
- ✓Cooling a board after IC replacement or reflow
- ✓Cooling after reballing a BGA chip
- ✓Moving soldering smoke away during micro-soldering
- ✓Heat control during charging port and charging IC repair
- ✓Cooling during desoldering on dead phone boards
- ✓Supporting soldering and desoldering on tablet and laptop PCBs
Compatible Devices
- ✓Universal board-repair accessory, not tied to specific phone models or chipsets
- ✓Smartphone motherboards (not brand-specific)
- ✓Tablet motherboards
- ✓Laptop PCBs
- ✓UV solder mask (green oil) on repaired boards
- ✓UV optical adhesive and UV glue on screen and component bonds
- ✓Boards cooling after IC reflow or reballing
- ✓Boards under soldering and desoldering that need smoke control
- ✓Boards held in a PCB holder at the microscope station
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What UV wavelength does the CUV-3 use, and can it cure green oil?
Is the Mechanic CUV-3 cordless, and how long does it take to charge?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



