MT6370P Power IC – MediaTek Sub-PMIC Charging & Display IC
₨ 650
MT6370P Power IC: Charger, Type-C and Display Power in One Package
The MT6370P Power IC is a MediaTek sub-PMIC that combines a single-cell Li-ion/Li-polymer switching charger, a USB Type-C and Power Delivery controller, dual flash LED current sources, an RGB indicator driver, a backlight WLED driver, a display bias driver and a general-purpose LDO in one 93-ball WLCSP package. When one of these blocks fails, you can see a phone that will not charge, a dead backlight, no flashlight or no Type-C detection. Mechanicpk supplies this IC for board-level technicians who diagnose MediaTek power rails precisely and need a genuine replacement chip for charging-section and display-power repairs.
MT6370P Power IC for Board-Level Charging and Display Power Repair
The MT6370P Power IC sits beside the main PMIC on MediaTek-based boards and handles the power functions that the main PMIC does not cover. MediaTek’s Linux kernel documentation describes the MT6370 as a highly integrated smart power management IC. It combines a single-cell battery charger, a USB Type-C and PD controller, flash LED and RGB LED drivers, a WLED backlight driver, display bias and an LDO. That integration makes the MT6370P power IC one of the most important chips to check when a MediaTek phone shows a charging fault together with display or flash symptoms. Mechanicpk stocks the MT6370P for technicians who prefer to replace one IC rather than chase faults across several separate chips.
What the MT6370 Sub-PMIC Integrates
Each block inside the MT6370 sub-PMIC links to a specific symptom on the bench. The switching charger controls current flow into the battery. It also provides an OTG boost output and BC1.2 charger-type detection, so it determines whether a USB flash drive or an OTG accessory receives power. The Type-C/PD controller handles cable orientation and power negotiation with the charger. The WLED backlight driver powers the LCD backlight, and the display bias driver supplies the positive and negative rails that the panel needs. The flash LED current sources drive the camera flash and torch, and the RGB driver controls the notification LED on boards that include one. If you know this layout before you lift the chip, a vague “dead phone” complaint becomes a targeted diagnosis.
Electrical and Package Profile
Distributor data lists the MT6370P/A in a 93-WLCSP package that measures 4.2 × 4.32 mm, with surface-mount construction. It lists two supply ranges, 2.7V–5.5V and 4V–14V. The 4V–14V range corresponds to the charger input side, which receives voltage from the adapter. The operating temperature rating runs from −40°C to 85°C. Because this is a wafer-level chip-scale package, the solder balls sit directly under the silicon die with no plastic body around them. Your rework process therefore needs controlled heat, good flux, and careful handling during removal and placement.
Fault Symptoms That Point to the MT6370P
Technicians usually look at the MT6370P power IC when a MediaTek phone shows one or more of the following problems:
- A charging issue where the phone shows no charging icon, charges very slowly or never reaches full charge
- A display problem where the image appears faintly but the backlight stays dark
- A flashlight or camera flash that has stopped working
- A Type-C port that no longer detects chargers or OTG devices
These symptoms often appear together after liquid damage or after someone uses a faulty charger, because a single failed IC takes out several functions at once. Measure the VBUS, battery and backlight output lines with a multimeter before you decide that the chip needs replacement. A shorted rail around the MT6370P often confirms the diagnosis quickly.
Replacement Workflow on the Repair Bench
Fix the board firmly in a PCB holder and inspect the area under a microscope. Shield nearby components before you heat the area with a hot air station. After you remove the old chip, clean and level the pads with a soldering station and solder wick. If you reuse a chip or work from a bare part, a reballing kit with a matching stencil prepares the balls correctly. Align the new MT6370P using its pin-1 marking, reflow it evenly, and test charging current, backlight output and flash operation before you reassemble the phone. A test box or USB ammeter confirms that the charger negotiates correctly with the adapter.
Why Source It from Mechanicpk
Board-level repair on charging circuits depends on genuine silicon. A mismatched or recycled chip can bring the original fault back within days. Mechanicpk supplies the MediaTek MT6370P charging IC for repair shops, service centers and training institutes across Pakistan. The same catalog carries the hot air stations, microscopes, reballing kits and PCB holders that this repair requires, so you can source the complete rework setup from one supplier.
| Weight | 0.1 kg |
|---|
Key Features
- ✓MediaTek sub-PMIC that combines charger, Type-C/PD, LED, backlight and display bias functions in one IC
- ✓Single-cell Li-ion/Li-polymer switching battery charger with OTG boost and BC1.2 detection
- ✓Integrated USB Type-C and Power Delivery controller for charger negotiation
- ✓Dual flash LED current sources for the camera flash and torch
- ✓WLED backlight driver and display bias driver for LCD panel power
- ✓RGB indicator LED driver and general-purpose LDO
- ✓Compact 93-WLCSP package (4.2 × 4.32 mm) for high-density boards
- ✓Rated −40°C to 85°C, with 2.7V–5.5V and 4V–14V supply ranges
Specifications
| Brand | MediaTek |
|---|---|
| Model | MT6370P (MT6370P/A) |
| Category | Sub-PMIC / Charging and Power Management IC |
| Compatibility | MediaTek platforms that use the MT6370 sub-PMIC |
| Supported Devices | Smartphones, tablets and portable devices |
| Technology | Single-cell switching charger with USB Type-C & PD controller, flash LED, RGB LED, WLED backlight and display bias drivers, LDO |
| Input Voltage | 2.7V–5.5V and 4V–14V (supply ranges) |
| Dimensions | 4.2 mm × 4.32 mm (93-WLCSP package) |
Common Repair Uses
- ✓Replacing the IC on phones that show no charging or a fake charging indication
- ✓Repairing a dead phone after a shorted charger rail or liquid damage
- ✓Restoring the LCD backlight when the display shows an image but no light
- ✓Fixing a display that has no output because of a failed display bias rail
- ✓Restoring the camera flash and torch function
- ✓Repairing USB Type-C charger detection and OTG power faults
- ✓Clearing a shorted rail around the charging section during board diagnosis
- ✓WLCSP reballing and rework practice in training institutes
Compatible Devices
- ✓MediaTek-platform smartphones that use the MT6370 sub-PMIC
- ✓MediaTek-platform tablets that use the MT6370 sub-PMIC
- ✓Portable devices built on MediaTek reference designs that use the MT6370P
- ✓MediaTek Genio 500 platform designs (listed by the distributor as the charger and accessory IC for Genio 500)
- ✓Boards that use a single-cell Li-ion/Li-polymer battery with MT6370-based charging
- ✓USB Type-C devices that use the MT6370 integrated PD controller
- ✓LCD-panel devices that draw backlight and display bias from the MT6370
- ✓Replacement only where the original board carries an MT6370P marking (confirm by reading the chip marking before ordering)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can a faulty MT6370P cause both a charging problem and a backlight problem?
What package does the MT6370P use, and can I reball it?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



