RF4 RF-FT03 Mobile PCB Repair Fixture – Three-Axis Clamp
₨ 3,999
Three-Axis Motherboard Fixture for Chip Rework
The RF4 RF-FT03 PCB repair fixture holds a mobile phone motherboard steady while you remove glue, lift a CPU or rework a BGA chip. Its three-axis clamp grips special-shaped boards, and the bidirectional movement lets you reposition the target area without re-clamping. Honeycomb heat dissipation and high-temperature resistance protect the surrounding components during hot air work. The fixture supports motherboards up to 70 mm in length, so it covers most phone boards that reach a Pakistani repair bench. Pair it with your hot air station and microscope to keep every IC change controlled and repeatable.
In stock
RF-FT03 PCB Repair Fixture for Stable Motherboard Rework
The RF4 RF-FT03 PCB repair fixture keeps a mobile phone motherboard locked in position while you work on CPU, chip and IC areas. RF4 builds it around a three-axis clamp, so it grips boards that a basic two-jaw holder cannot control, including special-shaped motherboards that arrive after drops, liquid damage or failed earlier repairs. The fixture supports boards up to 70 mm in length and moves in two directions, which lets you shift the board under your heat source without lifting it out of the clamp. Technicians in Pakistan who handle dead phone and hang on logo jobs every day gain a firmer base for hardware fault diagnosis and chip-level repair.
Three-Axis Clamp and Bidirectional Movement
Board shape decides how hard a fixture is to use. Many phone motherboards carry cutouts, stepped edges and uneven outlines, and a fixed rectangular jaw leaves them loose or forces you to hold them by hand. The RF-FT03 three-axis clamp adapts to these outlines, so the board stays put while you work. The bidirectional movement lets you slide the board toward or away from your nozzle or soldering tip. You bring the target chip into position, lock it and keep both hands free for tweezers, flux and a hot air gun. That control matters most during IC change karna jobs, where a board that shifts mid-rework can lift pads or knock neighbouring components.
Honeycomb Heat Dissipation and Chip Protection
Heat management protects the board during every long rework session. RF4 designs the RF-FT03 with a honeycomb structure that spreads heat away from the clamped area and supports high-temperature resistance. That keeps the fixture stable while hot air blows across the board. The unique three-layer board slot design is built so the fixture does not damage edge ICs on the motherboard. Edge-mounted chips often sit exactly where a clamp wants to grip, so this design helps you hold a populated board without crushing the components along its border. RF4 also designs the fixture for dual use with chips and CPUs, which makes it a practical single holder for both chip-level and CPU-level jobs.
Where It Fits in Your Repair Workflow
You place the RF-FT03 at the start of any board-level job, before you apply heat. Clamp the motherboard, position it under your microscope and set up your hot air station or soldering station. From there you handle the steps the fixture supports: fixing the PCB, removing glue from a CPU or IC, reworking a BGA chip and soldering a replacement. After the repair, you release the board and check rails and continuity with your multimeter. The fixture sits beside your other PCB holders, reballing kits and soldering tools, and it suits shops that already run a structured bench layout. Beginners gain a steadier hand on small boards. Experienced technicians gain repeatable clamping across dozens of boards per week, which cuts the time you spend re-aligning a board between heat cycles.
| Weight | 0.5 kg |
|---|
Key Features
- ✓Three-axis clamp that suits special-shaped motherboards
- ✓Bidirectional movement for repositioning the board during rework
- ✓Supports motherboards up to 70 mm in length
- ✓Honeycomb heat dissipation structure
- ✓High-temperature resistance for hot air work
- ✓Chip protection during rework
- ✓Three-layer board slot design that protects edge ICs
- ✓Dual-purpose design for chips and CPUs
Specifications
| Brand Entity | RF4 |
|---|---|
| Product Entity | RF4 RF-FT03 Three-Axis Multifunctional Universal Fixture |
| Technology Entity | Three-axis clamp, honeycomb heat dissipation, bidirectional movement |
| Compatible Device Entities | Mobile phone motherboards, special-shaped PCBs, CPU and chip boards |
| Repair Process Entity | BGA rework, IC change, CPU glue removal, PCB soldering |
| Industry Entity | Mobile phone repair, PCB repair, GSM hardware repair Pakistan |
Common Repair Uses
- ✓Board holding for chip-level and CPU-level rework on mobile phone motherboards.
- ✓Fixing a PCB securely during repair
- ✓IC chip removal and soldering
- ✓CPU glue removal
- ✓BGA rework
- ✓Soldering work on populated boards
- ✓Hot air rework with heat dissipation support
- ✓Holding boards with edge ICs without damage
- ✓Dual-purpose chip and CPU repair jobs
Compatible Devices
- ✓Universal mobile phone motherboard scope, not brand-specific. Verified for boards up to 70 mm in length.
- ✓Mobile phone motherboards up to 70 mm in length
- ✓Special-shaped (irregular outline) motherboards
- ✓Motherboards with edge-mounted ICs
- ✓Boards carrying a CPU for rework
- ✓Boards carrying chips and BGA ICs for rework
- ✓Compact single-board PCBs that need two-way repositioning



