Skyworks SKY77645-61 PA IC – 3G/4G LTE Power Amplifier

₨ 250

77645-61 PA IC for 3G and 4G Network Repair

The Skyworks SKY77645-61 is a SkyLiTE multimode multiband power amplifier module that drives the transmit side of a smartphone’s 3G and 4G LTE radio. When a phone shows no service, drops calls on the first ring, or pulls heavy current on the battery line, a failed PA often sits at the root of it. This replacement IC gives you the exact part marking your board needs, so the baseband can control the PA again over its MIPI interface. Mechanicpk supplies it for board-level technicians who handle network faults, PA shorts, and RF section rework daily.

13 People watching this product now!
Description

Skyworks 77645-61 PA IC: Transmit Power for the Multiband RF Section

The 77645-61 PA IC belongs to Skyworks’ SkyLiTE family, a line of multimode multiband (MMMB) power amplifier modules built for 3G and 4G handsets. Inside one surface-mount package, it combines the WCDMA/LTE amplifier blocks, a Multi-Function Control (MFC) block, and RF input/output ports matched to 50 Ω. That integration means a single chip carries the transmit load for several cellular bands at once. When it fails, the phone loses its ability to talk to the tower, even though the receive path may still show partial signal bars. For a technician, that symptom pattern points straight at the PA section.

How the SKY77645-61 Works Inside the Phone

The baseband processor sends a low-level RF signal from the transceiver into the PA input. The module raises that signal to transmission power and routes it through its band outputs toward the duplexers and antenna switch. A CMOS control die inside the package receives commands over the MIPI RFFE bus, selecting the active band, mode, and bias setting. Skyworks optimises the SKY77645 family for Average Power Tracking (APT), so a DC-DC converter adjusts the PA’s VCC to match each output power level. You get lower current draw during light transmission and full output only when the network demands it. That design explains why a PA fault often shows up on the power rail before it shows up anywhere else.

Diagnosing a Faulty 77645-61 PA IC

PA failures tend to fall into two groups. The first is the dead-short case: the PA’s battery or VCC supply line collapses to ground, so the phone draws high current on the DC power supply, heats up near the RF shield, or refuses to boot at all. Inject a controlled voltage into the shorted line and use rosin or a thermal camera to confirm the PA itself heats first. The second group covers RF faults: the phone powers on normally but shows “No Service”, “Emergency calls only”, or loses network as soon as a call connects. Here, check the PA supply voltage, the MIPI clock and data lines, and the solder joints under the module before you commit to IC change karna. A phone that recently suffered water damage or a drop often shows cracked joints on these pads.

Replacement Workflow on the Repair Bench

Remove the RF shield cleanly and protect nearby duplexers and filters with heat-resistant tape. Use a hot air station with a medium-airflow nozzle and preheat the board from below on a PCB holder or preheater, since the multilayer laminate pulls heat quickly. Lift the old module once all pads reflow, then clean the footprint with flux and solder wick until every pad sits flat. Tin the new SKY77645-61 lightly, align it under a microscope, and reflow until it self-centres. After cooling, measure the supply line for shorts before you power on, then confirm network registration, voice calls, and mobile data uplink.

Matching the Exact Part Marking

Skyworks produces several variants within the SKY77645 line, and the suffix after the dash identifies the exact build. Always match the full 77645-61 marking from the board or the schematic before you order. A wrong variant may physically fit the footprint but fail band selection or MIPI configuration on that specific motherboard. For a related upgrade on your RF bench, pair this IC with a reliable reballing kit and a microscope so you handle fine-pitch PA modules without bridging pads.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Multimode multiband power amplifier module from Skyworks’ SkyLiTE family
  • Covers 3G and 4G LTE transmit paths in one package
  • Integrated WCDMA/LTE amplifier blocks with 50 Ω matched RF ports
  • On-board Multi-Function Control block for band and mode selection
  • Fully programmable through the MIPI RFFE interface
  • Optimised for APT DC-DC operation to cut current draw
  • InGaP/GaAs process for efficient, linear output
  • Exact -61 suffix for correct board-level replacement

Specifications

BrandSkyworks Solutions
ModelSKY77645-61
CategoryMobile Phone ICs > Power Amplifier (PA) ICs
TechnologyInGaP/GaAs multimode multiband power amplifier module (SkyLiTE family), MIPI RFFE control, APT DC-DC optimised
Supported DevicesSmartphone motherboards whose schematic or board marking lists SKY77645-61

Common Repair Uses

  • No service / “Emergency calls only” faults traced to the PA
  • Network drops as soon as a call connects
  • Mobile data works on Wi-Fi only, with no cellular uplink
  • Dead phone caused by a shorted PA supply line
  • Heating near the RF shield with high current draw
  • Battery drain from PA leakage on the VBAT line
  • Post-water-damage RF section rework
  • Cracked PA solder joints after a drop or board flex

Compatible Devices

  • Verified at chipset-family and board-marking level. Device-model fitment depends on the phone’s schematic.
  • Smartphone boards that carry the SKY77645-61 marking in the PA section
  • 3G WCDMA / HSDPA / HSUPA / HSPA+ handsets using the SKY77645 PA family
  • 4G LTE FDD multiband handsets
  • 4G LTE TDD handsets
  • TD-SCDMA-capable handsets
  • RF front-ends that control the PA over the MIPI RFFE bus
  • Boards that feed the PA through an APT DC-DC converter
  • Not universal: match the full part suffix before replacement

FAQ

What is the product name?
The product name is Skyworks SKY77645-61 PA IC.
What is the brand of this product?
The brand of this product is Skyworks Solutions.
What is the model of this product?
The model of this product is SKY77645-61.
What is this product used for?
This product is used for replacing a faulty 3G/4G power amplifier module on smartphone motherboards to restore network, calls, and mobile data.
Which devices are compatible with this product?
This product is compatible with smartphone motherboards whose schematic or board marking lists the SKY77645-61 power amplifier module.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can a shorted 77645-61 PA IC make a phone completely dead?
Yes. The PA draws power from the battery or DC-DC supply line, so an internal short pulls that line down and the phone may not boot. Confirm it by injecting a controlled voltage into the line and checking which component heats first.
Does the 77645-61 PA IC need any software or programming after replacement?
No programming is required. The baseband controls the PA over the MIPI bus at runtime, but you must fit the exact 77645-61 variant so band and mode selection match the board’s configuration.