SMB1355 001-04 Charger IC for Xiaomi MIX3 – Qualcomm

₨ 300

Qualcomm SMB1355 Parallel Charger IC for Xiaomi MIX3

The SMB1355 001-04 Charger IC for Xiaomi MIX3 is the Qualcomm parallel charging buck regulator that shares battery current with the phone’s main PMIC charger. You use it to restore fast charging, fix slow charging, and clear no-charge faults on Mi MIX 3 logic boards where the original chip has shorted or failed. Qualcomm rates the SMB1355 at up to 94% efficiency at 3 A battery current, and the chip works with HVDCP adapters and Quick Charge technology. Match the 001-04 marking on your board before replacement, and fit it with a controlled hot air station, quality flux, and a stable PCB holder.

20 People watching this product now!
Description

SMB1355 Charger IC for Xiaomi MIX3: Qualcomm Parallel Charging Explained

The SMB1355 charger IC handles the parallel half of the charging system inside the Xiaomi Mi MIX 3. Qualcomm built the SMB1355 as a high-efficiency buck regulator that pairs with its standalone charger family, so the two chips split battery current between them. This split spreads heat across the board and lets the phone accept higher charge current without overheating the chassis. When this chip fails, your customer usually reports slow charging, no fast charging, heating near the charging section, or a phone that refuses to charge at all. This listing covers the SMB1355 001-04 Charger IC for Xiaomi MIX3, supplied for board-level replacement work by technicians who already handle IC-level charging repairs.

How the SMB1355 Fits the MIX 3 Charging Path

The Mi MIX 3 runs on the Snapdragon 845 platform and supports 18W wired fast charging with Quick Charge 4+. The main PMIC charger controls the charge cycle, while the SMB1355 acts as the parallel stage that adds current once the adapter negotiates a higher-power profile. Qualcomm rates the chip at up to 94% efficiency at 3 A battery current and lists compatibility with a wide range of HVDCP travel adapters and Quick Charge technology. That efficiency figure matters on a slim flagship board, because less wasted energy means less heat near the battery connector and the processor shield. Once you understand this division of work, you diagnose faster: a phone that charges slowly but still charges often points toward the parallel stage rather than the main charger.

Diagnosing an SMB1355 Fault Before IC Replacement

Start with a USB tester on a Quick Charge adapter and a known-good cable. A healthy MIX 3 draws clearly higher current during the fast-charge phase, so a board stuck at standard current suggests the parallel path has dropped out. Next, power the board from a regulated DC power supply and look for heat with a thermal camera or rosin smoke. A shorted SMB1355 heats up within seconds and pushes the supply into current limit, which often presents as a dead phone the moment you connect power. Switch your multimeter to diode mode and compare readings on the lines around the chip against a known-good board. Confirm the 001-04 marking on the original part before you order, since charger ICs with similar footprints carry different markings across Qualcomm platforms.

Replacement Workflow on Your Repair Bench

Lock the MIX 3 board in a PCB holder and shield the surrounding parts with heat-resistant tape. Apply a thin layer of quality flux, then lift the old chip with your hot air station at a controlled temperature and moderate airflow so you keep the small passives around it in place. Clean the pads with solder wick and fresh flux, then inspect them under a microscope for lifted or bridged pads before you continue. Tin or reball the new SMB1355 with the correct stencil from your reballing kit, align it against the board markings, and reflow it evenly. After cooling, clean the flux residue, recheck the charging lines for shorts with your multimeter, and test the phone on both a standard adapter and a Quick Charge adapter before you close the housing.

Tools That Complete an SMB1355 Repair

A clean SMB1355 job depends on bench accuracy more than speed. A hot air station with stable temperature control, a microscope for pad inspection, and a reballing kit with the right stencil cover the core of the work. A regulated DC power supply and a USB tester confirm the result before handover, so you return the phone with verified fast charging rather than a guess. Keep your multimeter and PCB holder within reach for short tracing on the charging line. If charging faults land on your bench every day, a thermal camera is the logical upgrade, because it pinpoints shorted charger ICs on Qualcomm boards in seconds and cuts diagnosis time on every SMB1355 charger IC job that follows.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Qualcomm SMB1355 parallel charger IC with 001-04 marking
  • High-efficiency buck regulator topology for parallel charging
  • Up to 94% efficiency at 3 A battery current (Qualcomm rating)
  • Works alongside Qualcomm’s standalone charger family
  • Supports HVDCP travel adapters and Quick Charge technology
  • Spreads charging heat to keep chassis temperature lower
  • Direct replacement for the Mi MIX 3 parallel charging stage
  • Suits standard hot air and reballing workflows

Specifications

BrandQualcomm
ModelSMB1355 (marking 001-04)
CategoryMobile Phone Charger IC – Parallel Charger
CompatibilityXiaomi Mi MIX 3
TechnologyHigh-efficiency buck regulator for parallel charging; up to 94% efficiency at 3 A battery current; HVDCP adapter and Qualcomm Quick Charge compatible

Common Repair Uses

  • Slow charging on the Xiaomi Mi MIX 3
  • Fast charging or Quick Charge not working
  • No-charge fault traced to the parallel charger stage
  • Heating around the charging section during charging
  • Dead phone with a short on the charging line traced to the SMB1355
  • Charger IC replacement after liquid damage near the charging area
  • Restoring charging after a failed previous rework
  • Charging section rebuilds in service centers and training institutes

Compatible Devices

  • Verified at device level for the Xiaomi Mi MIX 3; wider use depends on matching the 001-04 marking
  • Xiaomi Mi MIX 3
  • Boards that carry the SMB1355 with the 001-04 marking (match the marking before replacement)
  • Qualcomm parallel charging designs that pair the SMB1355 with a QTI standalone charger

FAQ

What is the product name?
The product name is SMB1355 001-04 Charger IC for Xiaomi MIX3.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is SMB1355 with the 001-04 marking.
What is this product used for?
This product is used for replacing a faulty parallel charger IC to fix slow charging, fast charging failure, and no-charge faults on Xiaomi Mi MIX 3 boards.
Which devices are compatible with this product?
This product is compatible with the Xiaomi Mi MIX 3 and boards that carry the SMB1355 with the 001-04 marking.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
How do I check if the SMB1355 is faulty on a Xiaomi MIX 3?
Power the board from a DC power supply and check for fast heating on the chip with a thermal camera or rosin, then compare diode mode readings on its lines against a good board. A USB tester showing no fast-charge current on a Quick Charge adapter also points to the parallel stage.
Can a Xiaomi MIX 3 still charge if the SMB1355 fails?
If the chip fails open, the main PMIC charger can often still charge the battery at reduced current, which shows up as slow charging. If the chip fails short, it can load the charging line and cause no charging, heating, or a dead phone, so replacement becomes necessary.