i2C C09 Digital Waveform Ammeter Charge Detection

₨ 19,000

Waveform Ammeter for Mobile Repair

The i2C C09 Digital Waveform Ammeter / Voltage Measurement With Charge Detection gives your repair bench a dual-channel 0-40V, 0-8A power-path tester with a 4.0-inch IPS screen. You watch current and voltage as a live curve, a pointer dial or digital numbers, so a dead phone that draws almost nothing looks different from a shorted board that pulls amps. The C09 also runs 140W full-protocol charging tests, millisecond-level dynamic voltage measurement and fast diode scanning, and it supports online firmware upgrades and PC screen projection. Technicians who want a spec-driven mobile phone charging tester get boot current, charging analysis and short hunting in one compact unit.

In stock

12 People watching this product now!
Description

Waveform Ammeter for Mobile Repair: i2C C09 Technical Overview

The i2C C09 Digital Waveform Ammeter / Voltage Measurement With Charge Detection replaces the guesswork of a plain bench supply readout with a live picture of what your board draws. A good waveform ammeter for mobile repair shows when current starts, spikes, stalls or drops, and the C09 packs that view into an 11.4 x 9.3 x 2.9 cm unit with a 4.0-inch IPS screen at 320 x 480 resolution. Two measurement channels accept 0-40V DC input and detect up to 8A, which covers everything from a dead phone that draws almost nothing to a shorted rail that pulls amps.

How the Three Display Modes Change Your Diagnosis

Numbers alone hide a lot of faults. The C09 gives you pointer, curve and digital modes, and you switch between them depending on the question you ask. Digital mode reads voltage, current and power at a glance when you confirm a normal boot current. Curve mode draws the waveform, so you see a boot loop issue as a repeating current pattern instead of a flickering number. Pointer mode reacts quickly with low visual noise, which helps when you need a fast estimate of the current range while you probe a board.
The unit measures dynamic voltage changes at millisecond level, so brief drops and spikes during power-on do not slip past you. Technicians who chase hang on logo cases and dead after flash cases get a timeline of the current draw rather than a single frozen reading.

Charge Detection and 140W Protocol Testing

Charging issue complaints reach every workshop daily, and the cause often sits in the charger, the cable, the port or the charging IC. The C09 tests full-protocol charging power up to 140W, so you read what a charger negotiates and delivers. You compare a third-party adapter against a known good one by watching the waveform, and you confirm whether a phone pulls the power it should after you replace a charging port or IC.
For bench work, the banana plug outputs supply up to 40V at 8A, and the USB output supplies up to 20V at 2A. Built-in protection engages at voltages below 60V and currents below 15A, which gives your board an extra layer of safety when you probe a questionable rail. Voltage resolution reaches 1mV and current resolution reaches 0.1mA, so small leakage paths show up clearly.

Diode Scan and Multimeter Functions on the Same Bench

Short hunting takes patience when you test each capacitor and line one by one. The C09 offers ultra-fast diode scanning with a 0-2.8V diode test range, and the extended edition with the built-in multimeter board adds resistance measurement up to 50K and positive or negative voltage measurement from 0-24V. Confirm which edition you order, because the multimeter functions depend on that board. You keep one device on the bench for current waveform, voltage check and diode scan instead of switching tools mid-repair.

Where the C09 Fits in Your Repair Workflow

The C09 sits at the start and end of most board-level jobs. You measure standby and boot current before you open the phone, you track the current while you apply heat with your hot air station or reflow a suspect IC, and you verify the repair once you reassemble the board. After you finish IC change karna work, a clean current curve confirms the board settles into a normal state. The same test closes out a reballing job, a PMIC swap or a charging port replacement.
Shops in Pakistan handle a steady stream of boot loop issue, network issue and display problem phones, and many of those faults trace back to a power rail that behaves wrongly under load. A current waveform narrows the search quickly: a rail that draws too much points you toward a short, while a rail that draws too little points you toward an open path or a missing enable signal. You decide where to probe next based on evidence rather than habit, which saves bench time on every job.
You can also connect the C09 to a computer for screen projection, which turns a small display into a large one for training, shared diagnosis or recorded repair content. Online firmware upgrades keep the unit current without hardware changes.

Pair It With the Rest of Your Bench

The C09 reads power behavior, and other tools handle the physical repair. Technicians usually pair it with a multimeter for continuity checks, a microscope for inspecting solder joints, a soldering station and hot air station for rework, a PCB holder for stable board handling, and a reballing kit for BGA work. For flashing and storage jobs, ISP pinout tools, eMMC programmers and UFS adapters sit in the same workflow, and the C09 helps you confirm that the board still draws normal current after you write or replace memory.
Mechanicpk stocks the i2C C09 for repair shops, service centers and technical institutes in Pakistan that want measured evidence behind every fault call. Choose it when your workflow needs waveform visibility, charging analysis and quick diode scanning in one compact instrument.

Additional information
Weight0.15 kg
Q & A
Please login to post questions

Key Features

  • Dual-channel 0-40V voltage and 0-8A current measurement
  • 4.0-inch IPS high-brightness display at 320 x 480
  • Pointer, curve and digital display modes
  • Millisecond-level dynamic voltage measurement
  • Ultra-fast diode scanning, 0-2.8V test range
  • 140W full-protocol charging power test
  • Over-voltage (<60V) and over-current (<15A) protection
  • Online firmware upgrade and PC screen projection

Specifications

Brandi2C
ModelC09
CategoryWaveform Ammeter / Mobile Repair Diagnostic Tester
CompatibilityUniversal. Measures any device or board powered within 0-40V DC and up to 8A; not device-specific
Technology4.0-inch IPS display (320 x 480), dual-channel voltage and current measurement, pointer / curve / digital display modes, online firmware upgrade, PC screen projection
Input Voltage0-40V DC (device power supply 5V 2A)
Output VoltageBanana plug 40V 8A; USB 20V 2A
Power Rating140W full-protocol charging power test
Dimensions11.4 x 9.3 x 2.9 cm

Common Repair Uses

  • Real workshop scenarios where the C09 reads power behavior
  • Dead phone diagnosis by reading standby and boot current
  • Short hunting on a shorted power rail with diode scan
  • Boot loop issue and hang on logo analysis through the current waveform
  • Charging issue diagnosis on ports, cables and chargers
  • Charging IC and PMIC replacement verification
  • Post-flash power check on dead after flash phones
  • Hot air rework and reballing checks before and after reassembly
  • Charger and adapter output testing up to 140W

Compatible Devices

  • Universal compatibility scope; works with any device or charger within the 0-40V DC, 8A measurement range
  • Android smartphone mainboards (power-on and boot current testing)
  • iPhone mainboards (power-on and boot current testing)
  • Tablet mainboards within the 0-40V, 8A range
  • USB fast chargers and power adapters up to 140W protocol testing
  • Third-party chargers (compatibility and output verification by waveform)
  • Charging ports, cables and charging IC circuits
  • Phone batteries and battery connectors on the bench
  • Individual power rails and component lines for diode and voltage checks

FAQ

What is the product name?
The product name is i2C C09 Digital Waveform Ammeter / Voltage Measurement With Charge Detection.
What is the brand of this product?
The brand of this product is i2C.
What is the model of this product?
The model of this product is C09.
What is this product used for?
This product is used for measuring voltage and current waveforms, charging power, and diode behavior while diagnosing mobile phone and PCB faults.
Which devices are compatible with this product?
The C09 has a universal scope. It works with any device, board or charger within its 0-40V DC and 0-8A measurement range, and it does not depend on a specific phone model.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What voltage and current range does the i2C C09 measure?
It measures 0-40V DC input on two channels and detects current up to 8A. Protection triggers below 60V and below 15A, and resolution reaches 1mV for voltage and 0.1mA for current.
Can the i2C C09 test 140W fast chargers?
Yes. The C09 supports 140W full-protocol charging power testing, so you check what a charger delivers and compare third-party chargers against a known good adapter.