YCS 2015 Plus Desoldering Wick (5pcs Roll)

₨ 1,350

Copper Desoldering Wick for Phone Boards

The YCS 2015 Plus desoldering wick gives your repair bench a 5pcs roll of braided copper solder remover with rosin flux built into the weave. The 2.0mm width fits connector pads, IC lands, and bridged pins on phone motherboards. You press the braid on the joint, heat it with your iron, and the molten solder climbs into the copper by capillary action. It leaves low residue, so board cleanup after an IC change stays quick. Mechanicpk supplies this wick to Pakistani technicians who need dependable pad cleanup for desoldering wick for mobile repair work.

In stock

19 People watching this product now!
Description

Desoldering Wick Built for Mobile Board Cleanup

The YCS 2015 Plus desoldering wick gives you braided copper solder remover sized for phone motherboards. Each 5pcs roll pack carries 2.0mm wide braid, rated at 1.5m length, with rosin flux already in the weave. You lay it on a pad, touch it with a hot iron, and the braid pulls molten solder upward by capillary action. Mechanicpk stocks it for technicians who clear bridges, level pads, and prepare boards after IC removal every working day.

Braid Construction and Flux Behaviour

The strip uses braided copper wire, which gives it strong thermal conductivity and a high tin pickup for its size. Rosin flux coats the braid, so routine cleanup needs no separate flux pen and the solder flows into the weave as soon as the iron heats it. The formulation leaves low residue, which shortens the alcohol cleaning pass after each pad.

The 2.0mm width suits the pads you meet on phone boards. It covers a connector pad row or a cluster of BGA lands without touching neighbouring components. Narrow braid fills fast and forces constant trimming, while wide braid soaks up heat your board cannot spare. At 2.0mm you balance both. Five pieces in the pack keep a fresh strip on your bench whenever a saturated one reaches its limit.

Where the YCS 2015 Plus Desoldering Wick Fits in Your Repair Workflow

Every hardware fault job that ends with an IC change starts with solder you must clear. After you lift a BGA chip with your hot air station, the pads carry uneven leftover solder, and a clean, flat surface decides whether the new IC seats properly. You drag the wick across those pads, level them, and move on to reballing.

The same braid handles charging port pads on a charging issue board, bridged pins on a display connector after a display problem repair, and rough joints a previous technician left behind. Pair it with a fine-tip iron from your soldering station, a microscope to confirm pad condition, and a PCB holder to keep the board steady.

Wick removes only exposed solder, so a component that covers its own pads, such as a BGA chip, must come off with heat first. The braid then finishes the job. Technicians who lift chips on dead after flash boards, boot loop issue boards with eMMC or CPU faults, or network issue boards with damaged RF ICs repeat this same cleanup step before they place the replacement.

Using the Wick Without Lifting Pads

Pads lift when you rush. Lay the braid flat over the solder, press the iron tip on top of the braid, and watch the solder turn the copper silver as it wicks. Lift the braid and the iron together in one motion while the solder stays molten. Drag a cooling braid and you tear copper off the board.

Once the strip fills with solder, cut that section off and expose fresh braid, because a saturated section pulls nothing. Match your iron tip to the pad size, check the result under the microscope, and wipe the area clean before you continue.

Wick also suits tight spots where a desoldering pump struggles, since it removes solder from small, isolated areas without stressing the whole board. Keep unused pieces sealed in the pack so the braid stays clean and oxidation-free until you need it. A multimeter check across the cleaned pads confirms no bridge remains before you power the board.

Additional information
Weight0.3 kg
Q & A
Please login to post questions

Key Features

  • Braided copper wire with strong thermal conductivity
  • Rosin flux coating on the braid
  • 2.0mm width suited to phone board pads
  • Strong tin absorption by capillary action
  • Low residue for faster board cleaning
  • 5pcs roll pack for repeated bench use
  • Handles pad leveling, bridge removal, and IC removal cleanup
  • Works with any soldering iron or soldering station

Specifications

BrandYCS
Model2015 Plus (5pcs Roll)
CategoryDesoldering Wick / Solder Braid
CompatibilityUniversal, not device-specific
TechnologyBraided copper wire with rosin flux
MaterialBraided copper
Dimensions2.0mm width × 1.5m length

Common Repair Uses

  • Solder removal and pad cleanup on phone and electronics boards
  • Pad leveling after BGA IC removal
  • Solder bridge removal on fine-pitch pins
  • Charging port pad cleanup
  • Display connector pin correction
  • eMMC and CPU pad cleanup before reballing
  • Removing excess solder after a hardware fault repair
  • Cleaning old joints before jumper wire soldering
  • Board preparation before a replacement IC goes on

Compatible Devices

  • Universal, works on any PCB with exposed solder; not device-specific
  • Android smartphone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno)
  • iPhone logic boards
  • Tablet motherboards
  • Laptop motherboards
  • BGA pads after IC removal
  • Charging port and connector pads
  • Display and battery connector pads
  • General electronics PCBs

FAQ

What is the product name?
The product name is YCS 2015 Plus Desoldering Wick (5pcs Roll).
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is 2015 Plus.
What is this product used for?
This product removes excess solder, clears solder bridges, and cleans pads on phone motherboards and other PCBs.
Which devices are compatible with this product?
This product works on any PCB with exposed solder, so it suits Android motherboards, iPhone logic boards, tablets, and laptops. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the YCS 2015 Plus desoldering wick have flux built in?
Yes. The braid carries rosin flux, so you can wick solder without adding flux for routine pad cleanup.
Can desoldering wick remove a BGA IC from the board?
No. Wick removes only exposed solder. Lift the BGA chip with a hot air station first, then use the wick to clean and level the leftover solder on the pads.