YCS 2023-006 Desoldering Wick (5pcs Roll) 2mm Braid
₨ 1,500
Fine 2.0mm Copper Desoldering Wick
YCS 2023-006 Desoldering Wick (5pcs Roll) gives your repair bench five pieces of woven pure copper braid, each 2.0mm wide and 1.5m long with a 0.06mm wire width. The braid pulls excess solder off phone-board pads by capillary action, so you can clean IC pads, fix bridged pins and prepare charging port or connector pads before the next joint. YCS describes the braid as oxidation resistant, anti-static and low in residue, and it works with a standard soldering iron or station. Mechanicpk supplies this desoldering wick for mobile repair to technicians, repair shops and service centers across Pakistan.
In stock
Precision Solder Removal With YCS 2023-006 Desoldering Wick
The YCS 2023-006 Desoldering Wick (5pcs Roll) is a pure copper braid that strips excess solder off phone-board pads without lifting tracks. If you search for a desoldering wick for mobile repair that suits fine-pitch work, this 2.0mm wide braid with a 0.06mm wire width fits that brief. Each pack gives you five pieces at 1.5m per piece, enough to keep several bench stations stocked through a busy week. Mechanicpk supplies it to Pakistani repair shops, service centers and training institutes that want consistent solder removal on every hardware fault job, from a dead phone to a charging issue.
Braid Construction and Technical Highlights
Copper does the heavy lifting in this braid. Woven copper strands carry heat from your iron tip into the joint, and the weave pulls molten solder upward through capillary action. YCS describes the material as oxidation resistant, anti-corrosion and anti-static, with low residue after use, which matters when you prepare pads for a fresh IC. The 2.0mm width covers most pads and bridged IC legs you meet on smartphone boards, and the 1.5m length per piece gives you plenty of fresh braid to trim as you work. You need no pump or vacuum tool, because the braid works with any standard iron or station tip that holds a stable temperature. Press the braid flat over the excess solder, then heat through the wick instead of dragging it across the pad. Once a section fills with solder, cut it off and continue with clean copper, because spent braid only soaks up heat.
Where This Wick Fits in Your Repair Workflow
Wick enters the job after the hard part. You lift a BGA chip, an eMMC or a connector with a hot air station, then clean the leftover solder on the board pads before you reball or reseat the part. Wick removes only exposed solder, so it cannot reach under a chip that still sits on the board. Technicians use it for IC removal cleanup, bridge correction between fine pins, charging port pad repair and display connector rework. On a dead phone that needs an eMMC swap or ISP wire soldering, clean pads decide whether the new joint holds. Check the finished pads under a microscope, confirm continuity with a multimeter, and clamp the board in a PCB holder before the next step.
Tin the tip of your iron lightly first so heat transfers faster. Lay the braid over the joint, press the tip on top for a second or two, and watch the solder travel up the weave. Lift the iron and braid together so the copper does not freeze onto the pad. Lead-free joints need a higher iron temperature than leaded ones, so adjust your soldering station before you start.
Choosing the 2023-006 Pack Over Other YCS Wick Sizes
YCS sells several braid options, and the model number tells you what you get. The 2023-006 measures 2.0mm wide and 1.5m long with a 0.06mm wire width. The sibling 2023-005 keeps the 2.0mm width but runs 2.3m long with a 0.05mm wire width, so pick it when you burn through braid fast on long jobs. The 3520 option widens to 3.5mm for larger pads. For a 2mm solder braid that handles daily phone repairs, the 2023-006 balances width and piece length and stores neatly on the bench. Buy the five-piece roll pack when several technicians share a workshop, so each person keeps a piece at their station. Mechanicpk also stocks soldering stations, hot air stations, reballing kits, microscopes and multimeters, so you can build the full wick-to-reball bench from one supplier.
| Weight | 0.3 kg |
|---|
Key Features
- ✓Pure copper woven braid for fast heat transfer into the joint
- ✓2.0mm width suited to phone-board pads and IC legs
- ✓0.06mm wire width weave
- ✓1.5m length per piece for repeated trimming
- ✓Oxidation resistant and anti-corrosion construction
- ✓Anti-static, low-residue use
- ✓Five pieces per roll pack for multi-technician benches
- ✓Works with a standard soldering iron or station, with no pump needed
Specifications
| Brand | YCS |
|---|---|
| Model | 2023-006 |
| Category | Desoldering Wick / Solder Braid |
| Compatibility | Universal – works with standard soldering irons and stations; not device-specific |
| Technology | Woven copper braid, capillary action solder absorption |
| Material | Pure copper |
| Width | 2.0mm |
| Length | 1.5m |
| Wire Width | 0.06mm |
Common Repair Uses
- ✓Pad cleanup and solder removal in board-level phone repair.
- ✓Cleaning pads after IC removal with a hot air station
- ✓Pad preparation before BGA reballing
- ✓Removing solder bridges between fine IC pins
- ✓Cleaning eMMC pads before an eMMC swap
- ✓Cleaning pads before ISP wire soldering on a dead phone
- ✓Charging port pad repair after a charging issue
- ✓Display and battery connector pad rework
- ✓Removing excess solder from through-hole and SMD joints
Compatible Devices
- ✓Universal – not device-specific. The braid works on the exposed solder of any PCB, so it suits phone motherboards of every brand.
- ✓Android smartphone motherboards
- ✓iPhone logic boards
- ✓Tablet PCBs
- ✓Feature phone boards
- ✓Smartwatch and wearable PCBs
- ✓BGA IC pads after chip removal
- ✓Charging port and connector pads
- ✓Display and battery connector pads
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the difference between YCS 2023-005 and 2023-006 desoldering wick?
Can desoldering wick remove solder under a BGA chip on a dead phone board?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



