YCS D11 High-Conductivity Low-Resistance Silver Paste
YCS D11 High-Conductivity Low-Resistance Silver Paste Original price was: ₨ 1,500.Current price is: ₨ 1,200.
Back to products

YCS 2020 PLUS Desoldering Wick (5pcs Roll)

₨ 1,600

Pure Copper Desoldering Wick, 5-Roll Pack

The YCS 2020 PLUS Desoldering Wick (5pcs Roll) delivers five rolls of woven pure copper braid, each 2.0 mm wide, for lifting leftover solder from phone mainboard pads. Capillary action pulls molten tin into the weave, so you clear BGA pads after IC removal, fix solder bridges and flatten connector lands without scraping the board. Technicians use it alongside soldering stations, hot air stations and reballing kits during charging port, PMIC and eMMC rework. Buy the YCS 2020 Plus desoldering wick from Mechanicpk for a reliable bench consumable built for Pakistani mobile repair shops.

In stock

11 People watching this product now!
Description

YCS 2020 Plus Desoldering Wick for Clean Pad Recovery

The YCS 2020 PLUS Desoldering Wick (5pcs Roll) gives your bench five rolls of woven pure copper braid for lifting leftover solder from phone mainboard pads. Each roll measures 2.0 mm wide, narrow enough for dense board-level work. A good YCS 2020 Plus desoldering wick wets fast, pulls tin cleanly and leaves a flat pad ready for reballing. This pack covers that job for a busy repair shop without forcing you to reorder single rolls every week.

Braid Construction and Technical Behaviour

YCS weaves this wick from pure copper strands, and copper gives you the fast heat transfer a phone board demands. When your iron tip touches the braid, heat travels through the strands into the solder beneath, and the molten tin climbs the weave by capillary action. The tight weave grips the tin without pushing it sideways, which helps you avoid new bridges between neighbouring pads. Supplier documentation for the YCS range describes good thermal conductivity, strong tin absorption, low residue and oxidation resistance. The 2.0 mm width suits the narrow pads on BGA footprints, connector lands and shield-frame joints, while the 2.0 m roll length gives you enough braid to trim away saturated sections again and again. Each of the five rolls works independently, so you can wear one down on heavy IC pads and keep a fresh roll for fine micro-work. Keep one limit in mind: wick removes only exposed solder, so you must lift an IC or shield before you clean the pads under it.

Where It Fits in Your Mobile Repair Workflow

Desoldering wick sits between two stages of every board-level job. A hot air station or soldering station frees the component first. The wick then clears the old tin from the pads so the next part sits flat. Without that cleanup, uneven solder mounds push a replacement IC off level and create the weak joints behind a charging issue or a dead phone that comes back a week later. Fix the board in a PCB holder, work under a microscope, and drag the braid across each pad until the surface shows a smooth, thin tin layer. Check continuity with a multimeter before you move to a reballing kit or fit the new chip. Technicians who handle charging port repair, display connector replacement, PMIC change and eMMC rework all reach for the same braid, which is why a five-roll pack disappears quickly on a busy bench. Repair shops across Pakistan handle high board volumes, so a consumable that behaves the same way roll after roll matters more than a headline spec.

Using the Wick Correctly on a Phone Board

Match the braid to the job and keep your technique consistent. Lay the wick flat over the pad or bridge so it covers the full solder build-up. Press your iron tip on top of the braid at roughly 45 degrees and wait for the tin to flow into the weave. Lift the iron and the braid together, because pulling one away early can bond the braid to the pad. Cut off the saturated section, since a clogged length cannot absorb more solder and can push flux residue back onto the board, then continue with fresh braid. Work with the lowest iron temperature that melts your solder cleanly, because excess heat lifts delicate pads on thin mainboards. A five-roll pack lets you keep a separate roll at each bench position, so no technician waits on another to finish pad cleaning. Mechanicpk offers the YCS 2020 PLUS Desoldering Wick (5pcs Roll) for repair shops and service centers that want a consistent consumable in volume.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Woven pure copper braid for fast heat transfer
  • Strong tin absorption through capillary action
  • 2.0 mm width for narrow phone board pads
  • 2.0 m roll length per roll
  • Low residue finish for easier pad inspection
  • Oxidation-resistant copper construction
  • Five-roll pack for multi-bench shops
  • Works with any standard soldering or hot air station setup

Specifications

BrandYCS
Model2020 PLUS
CategoryDesoldering Wick / Solder Braid
CompatibilityUniversal, not device-specific
TechnologyWoven copper braid with capillary solder absorption
MaterialPure copper braid
Width2.0 mm
Length2.0 m per roll
Pack Quantity5 rolls

Common Repair Uses

  • Real bench scenarios where braid-based solder removal applies
  • Cleaning BGA pads after IC removal and before reballing
  • Removing solder bridges between fine-pitch pins
  • Flattening leftover tin on eMMC and UFS pads
  • Preparing pads for PMIC or charging IC replacement
  • Clearing old solder from charging port and connector lands
  • Cleaning shield frame pads after rework
  • Redoing a poor joint on a board with a hardware fault
  • Prepping pads for jumper wire repair on damaged traces

Compatible Devices

  • Universal solder removal tool for any PCB with exposed solder, not tied to specific phone models
  • Android phone mainboards (Samsung, Oppo, Vivo, Infinix, Tecno, Xiaomi)
  • iPhone logic boards
  • Charging port and sub-board PCBs
  • Display and battery connector pads
  • BGA pads on eMMC and UFS memory footprints
  • PMIC and charging IC footprints
  • Shield frame and RF can pad areas
  • Laptop and other electronics PCBs

FAQ

What is the product name?
The product name is YCS 2020 PLUS Desoldering Wick (5pcs Roll).
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is 2020 PLUS.
What is this product used for?
This product removes leftover solder from PCB pads and clears solder bridges during mobile phone board repair.
Which devices are compatible with this product?
This product works on any PCB with exposed solder, so it suits Android mainboards, iPhone logic boards and charging or display sub-boards. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What width is this desoldering wick and which pads does it suit?
Each roll is 2.0 mm wide, which suits narrow pads such as BGA footprints, connector lands and shield frame joints. For a larger pad, choose a wick equal to or slightly wider than the pad.
Can this wick clean BGA pads on a dead phone board?
Yes, once the IC is off. Wick removes only exposed solder, so lift the chip with a hot air station first, then drag fresh braid across each pad to leave a flat tin layer before you reball.