B5819W SL SMD Schottky Diode SOD-123 40V 1A (5Pcs)
₨ 100
Low-Drop SOD-123 Rectifier for Power Path Repair
This pack gives you five B5819W Schottky diodes in the SOD-123 surface-mount package, carrying the “SL” marking code you find on the board. Each diode handles 40V repetitive peak reverse voltage and 1A average rectified current, with a maximum forward drop of 0.6V at 1A. That low drop keeps more voltage on the rail, which makes this part a natural choice for charging paths, polarity protection, and DC-DC boost outputs. When a board shows a charging issue or a dead rail and your diode test points to a shorted or open SL part, you swap it directly without hunting for a substitute.
B5819W Schottky Diode: Verified 40V / 1A Rectifier in SOD-123
The B5819W Schottky diode is a 1A, 40V surface-mount rectifier that manufacturers mark with the code “SL” on the SOD-123 body. When you open a charger board, a power bank, or a small DC-DC section and read “SL” next to a cathode band, this is the part you are looking at. Its Schottky barrier construction gives you a maximum forward voltage of 0.6V at 1A and 0.9V at 3A, far below a standard silicon junction rectifier at the same current. That difference matters on low-voltage rails, where every tenth of a volt decides whether a circuit starts cleanly or browns out. This pack supplies five pieces, so you keep spares on your repair bench for repeat jobs instead of reordering one diode at a time.
Electrical Ratings That Define Where It Fits
The datasheet sets the B5819W at 40V repetitive and non-repetitive peak reverse voltage, 28V RMS reverse voltage, and 1A average rectified output current. Repetitive peak forward current reaches 1.5A. Reverse breakdown starts at a minimum of 40V, and junction temperature tops out at 125°C. Distributor data lists leakage of up to 1mA at rated reverse voltage and diode capacitance in the 110–120pF range at 4V. These numbers tell you exactly where the part belongs: 5V USB charging lines, 12V adapter inputs, 3.7V battery paths, and boost converter outputs that stay under 40V. They also tell you where it does not belong, such as mains-side rectification or any rail that exceeds the 40V reverse limit. Match these ratings against the original part before you commit to the swap, and your replacement holds up under load.
Reading the SL Marking and Confirming a Fault
The SL code saves you time during fault-finding. Instead of guessing from package shape alone, you identify the B5819W from its two-letter marking and the cathode band at one end of the SOD-123 body. Switch your multimeter to diode mode, put the red probe on the anode and the black probe on the banded cathode, and a healthy Schottky shows a low forward reading. Reverse the probes and the meter should show open. A reading near zero in both directions means a shorted diode, a classic cause of a dead rail or an adapter that cuts out the moment you plug it in. An open reading in both directions points to a failed junction that blocks the power path entirely, which often shows up as a charging issue with no current draw at all.
Replacing a SOD-123 Schottky Diode on the Board
Swapping a SOD-123 Schottky diode takes a fine soldering iron tip or a hot air station at moderate airflow, flux, and tweezers. Lift the faulty part, clean the pads with solder wick, and tin them lightly. Place the new B5819W with its cathode band facing the same direction as the original, because reversed polarity puts the diode in conduction where the circuit expects blocking. Reflow both terminals, inspect the joints under a microscope, and re-run the diode test before you power the board. Mechanicpk recommends checking the downstream rail with your bench power supply after the swap, so you confirm current draw looks normal before the board goes back into its housing. A clean replacement here often brings a hardware fault back to working condition within minutes.
Where This Part Sits in Your Repair Workflow
The B5819W sits in the diagnostics and component-replacement stages of board-level repair. Pair it with a digital multimeter for testing, a soldering station or hot air station for removal, and a PCB holder to keep the board steady. A stereo microscope helps you read the SL marking clearly and verify the cathode band orientation on dense boards. For technicians who regularly service power sections, keeping a small stock of common SMD diodes alongside this one turns most power-path faults into same-day repairs.
| Weight | 0.1 kg |
|---|
Key Features
- ✓SL marking code for fast on-board identification
- ✓40V repetitive peak reverse voltage
- ✓1A average rectified output current
- ✓0.6V maximum forward voltage at 1A
- ✓1.5A repetitive peak forward current
- ✓Compact SOD-123 surface-mount package
- ✓Cathode band for clear polarity orientation
- ✓Pack of 5 pieces for bench stock
Specifications
| Model | B5819W |
|---|---|
| Category | SMD Schottky Diode |
| Compatibility | Circuits with a SOD-123 footprint operating within 40V reverse voltage and 1A average current |
| Supported Devices | Universal — not device-specific |
| Technology | Schottky barrier rectifier, 0.6V maximum forward voltage at 1A |
| Dimensions | SOD-123 surface-mount package |
Common Repair Uses
- ✓Power-path diagnostics and component replacement on low-voltage boards
- ✓Replacing a shorted diode that causes a dead rail
- ✓Replacing an open diode that blocks charging
- ✓Restoring reverse-polarity protection on DC inputs
- ✓Repairing boost converter output diodes
- ✓Fixing power OR-ing between USB and battery supplies
- ✓Repairing charger and adapter output sections
- ✓Restoring power bank charging and output circuits
- ✓Stocking spares for repeat power-section repairs
Compatible Devices
- ✓Universal — not device-specific; fits any circuit designed for a SOD-123 Schottky rectifier within 40V / 1A
- ✓Boards using the SOD-123 diode footprint
- ✓5V USB charging input circuits
- ✓3.7V lithium battery power paths
- ✓12V DC adapter input sections
- ✓Boost converter output stages up to 40V
- ✓LED backlight boost circuits within rating
- ✓Power bank charge and discharge boards
- ✓Small DC-DC converter modules
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I test an SL B5819W diode with a multimeter?
Can I replace an SS14 diode with the B5819W?
Related products
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



