Medusa Pro II UFS BGA-254 Socket Adapter
₨ 29,000
UFS BGA-254 Socket for Medusa Pro II Workflows
The Medusa Pro II UFS BGA-254 socket holds 254-ball UFS storage packages for direct work on the Medusa Pro II programmer. It matches the BGA-254 footprint, so a chip removed from a board can be read, written, or checked without soldering it onto a fixture. Technicians use it for chip-off storage work, dead boot recovery, and firmware verification. The socket suits service centers and workshops that handle UFS-based smartphones and tablets and need a repeatable way to connect the chip to the box.
Medusa Pro II UFS BGA-254 Socket for Chip-Off Storage Work
When a UFS-based phone or tablet stops booting, the storage package is often the first suspect. The Medusa Pro II UFS BGA-254 socket gives your bench a direct route to that chip. It is built for the 254-ball UFS footprint, so a chip lifted from the board can be seated and worked on without soldering it to a separate adapter board. Shops that handle dead boot cases, board-level storage recovery, and firmware reads will find that this socket closes the gap between the programmer and the chip itself. Every BGA-254 UFS package follows the same ball grid, so one socket covers the whole family of devices in that size rather than a single model at a time.
Seating the Chip Correctly
Seat the package with its ball A1 corner matched to the socket marking before you connect the box. Orientation errors are the most common reason a read returns no response, and a wrong seat can also stress the contacts. Check orientation twice, then check that the package sits flat in the socket body before you start a job. Keep the contact surfaces free of flux residue and dust, because residue raises contact resistance and produces unstable reads that look like a faulty chip. Handle the socket by its body rather than its contacts, and store it in a clean, dry case when it is not in use. A few minutes of careful seating saves a lot of time chasing false errors later.
Pairing with the Medusa Pro II Box
The socket is made for the Medusa Pro II programmer box. Distributor documentation states that the box reaches UFS devices through the standard MPHY and MPHY-II protocol, and that BGA-254 adapters are offered for that setup. The same box also handles eMMC and JTAG work, which means one station can cover several storage and debug tasks in the same shop. Confirm the chip is supported in the current Medusa Pro II software before you start a job, since supported chip lists change between software releases. Match the package size first, then confirm the device model in the software. That two-step check prevents most wasted sessions at the bench.
Common Jobs on the Bench
The socket earns its place in three common situations. The first is dead boot recovery. When a device fails after a bad update or an interrupted flash, reading the UFS chip off the board lets you back up the stored data and rewrite a clean image. The second is firmware verification. Reading the chip before you change anything shows you what is on it, so you can compare it against a known good image. The third is board fault isolation. Testing a suspect UFS package on the socket shows whether the storage itself has failed, which tells you whether to spend time on the surrounding power and signal circuit. Many Pakistani workshops handle these cases as dead phone jobs, and separating a storage fault from a board fault early keeps repair time and parts costs under control.
Who This Socket Suits
This socket fits technicians who already work with UFS chip-off, service centers that run a Medusa Pro II box, and technical training institutes that teach storage repair on real packages. It is a practical choice when your intake includes UFS devices in the BGA-254 size. If most of your work involves eMMC packages in other sizes, confirm that your box setup covers those packages before you buy, so your toolset matches your actual job mix. Matching the socket to your device mix keeps the tool in regular use instead of sitting on the shelf.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Socket built for the 254-ball UFS BGA footprint
- ✓Designed to pair with the Medusa Pro II programmer box
- ✓Supports MPHY and MPHY-II protocol access per distributor documentation
- ✓Allows removal and reseating of UFS packages without re-soldering
- ✓Suits chip-off reads, writes, and firmware verification
- ✓Fits dead boot and storage fault isolation workflows
- ✓Reduces board-level test time by separating storage faults early
- ✓Useful for service centers and technical training environments
Specifications
| Brand | Medusa |
|---|---|
| Model | Medusa Pro II UFS BGA-254 Socket |
| Category | UFS BGA-254 Socket Adapter |
| Compatibility | Medusa Pro II programmer box |
| Supported Devices | UFS BGA-254 storage packages |
| Technology | UFS, MIPI MPHY and MPHY-II protocol access |
Common Repair Uses
- ✓Verified workflows where this socket is used
- ✓Dead boot recovery on UFS-based devices after failed or interrupted flashing
- ✓Chip-off reading of BGA-254 UFS storage for data backup
- ✓Writing a clean firmware image to a removed UFS package
- ✓Firmware verification before modifying stored data
- ✓Isolating storage faults from board-level power or signal faults
- ✓Testing suspect UFS packages outside the device
- ✓Reflashing storage after board-level storage repair
- ✓Workshop training on UFS chip-off procedures
Compatible Devices
- ✓Device brands supported through the Medusa Pro II box, scoped to the box level; device-specific compatibility depends on chip and software support
- ✓Samsung
- ✓Huawei
- ✓LG
- ✓Lenovo
- ✓Motorola
- ✓Oppo
- ✓Sony
- ✓Xiaomi
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which UFS package size does this socket accept?
Is a separate programmer needed to use this socket?
Related products
ICFRIEND Easy UFS 6-in-1 Socket for Easy JTAG Plus Box
In stock



